Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
while reprovisioning NRF-9160DK if i try Create JITP Certificates following issue observed.
There was an error generating the certificate: A Nordic Semiconductor product...
We are facing issues with the NRF7002. The device is able to connect to the network but does not receive a DHCP IP address when using a specific router. We using the NRF7002...
Based on sdk15.3, nrf connect app version 4.28.1 does the following: 1. Change the dfu code to the ble_app_hrs example, and the bootloader also enables pairing and binding;...
I have implemented NUS on device A and confirmed that it can be connected from a PC by making it the advertising sender.
Device B can scan device A's advertisements and...
Hello, I am using W25Q512NW ( https://www.winbond.com/resource-files/W25Q512NW%20RevB%2007192021.pdf) in my custom board. I want to store the sensor data in this flash.
...
Hello,
We have a BLE product using the nRF52840 and nRF Connect SDK. After upgrading our firmware to use nRF Connect v2.6.2 we intermittently get this assert from the SoftDevice...
Hello, I have a BLE Mesh application which is advertising the Mesh Beacon. If after mesh is enabled, I configure and advertisement for showing manufacturer data, the Mesh...
Hello,
Currently, we are using a bootloader on the nRF52832 with the nRF5 SDK, and we are considering migrating to the nRF52811.
We have identified two possible options...
I am using the nrf connect sdk manager to download a tool chain (any version) and they always error out with this error below. I am on WindowsARM 64. I am not sure that matters...
Hello,
I am using the following device and development kit:
Device: NORA-B106-00B (nRF5340)
nRF Connect SDK: 2.0.2
When an interrupt is configured on the GPIO...
Hi, in our project with the nRF5340 we desire use the nRF21540 to have a long conection for BLE, the problem is we don't have any pin free in the nRF5340 to manage the nRF21540...
I have configured new UART in zephyr.dts device tree like this" "/ { chosen { zephyr,console = &uart1; zephyr,shell-uart = &uart1; zephyr,uart-mcumgr = &uart1; zephyr,bt-mon...
my device acts as ble periph ,case BLE_GAP_EVT_DISCONNECTED in ble_evt_handler , if do m_conn_handle = BLE_CONN_HANDLE_INVALID,current changed to 2.5mA, if dont, current is...
Hi,How can I force mcuboot to use a specific serial port for logging?
chosen {
zephyr,uart-mcumgr = & uart0 ;
zephyr,console = & uart1 ;
zephyr,shell-uart = & uart1...
