I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
Hi everyone,
what are the tolerances of the internal reference voltage of the ADC (0.6V) at room temperature? I know the tolerances are included in the gain error and are...
Hello,
I'm following this documentation Doc to include Fota upgrade on peripheral LBS sample but I have the following problems:
1) all file .bin like ( app_update.bin...
I'm using dongle nRF52840 to sniff packets between earphone & iPhone.
I am facing the same problem: " Encrypted packet decrypted incorrectly (bad MIC)"
just after LL_ENC_REQ...
HI,
I'm developing it using NRF52832.
I'm updating the remaining battery capacity using saadc. However, the battery value is not stable because the value obtained from...
Hello,
Following to this ticket , I started with an existing Segger embedded studio project from the SDK to port my project from Keil to SES 5.62 .
Now, the project works...
How long does it take to perform a soft reset (using sd_nvic_SystemReset()/NVIC_SystemReset())?
Looking at power measurements (attached) it seems to take about 730 ms (...
Hello developers,
I would like to combine BLE Central with USB HID. I am using the SDK example "BLE_Central_multilink", I can get signal from BLE modules.
Now I want...
I tried to program the Blinky sample which just blinks an LED to the Network core of the nRF5340 DK but doesn't seem to work. However, when I look at the docs I do see that...
Hi
I am a beginner of bluetooth
I want to build BLE connection between nrf52833 and nrf52810 as soon as possible (maybe in 100-200ms)
can I achieve that by config Advertising...
Hi Nordic,
I am facing strange behaviour with nrf9160 aws iot example where I am trying for fota update.
My device is sending data to AWS IOT every 5 minutes as it will...
Hello again Nordic World,
We have been using a couple of the Nordic dev boards (PCA10028, PCA10040) as uart central devices in our test system for a while and have just...
Hello,
I am using \nRF5_SDK_17.1.0_ddde560\examples\dfu\secure_bootloader\pca10040_s132_ble_debug, but when I bulid the proyect the following error appear:
.text is too...
Hello,
nRF SDK v16.0 , Softdevices s140_nrf52_7.0.1_softdevice and ANT_s340_nrf52840_6.1.1
Recently we wanted to add ANT to our BLE application. So we changed the softdevice...
I have an application that I can install and run on the nRF52840 dongle. But to program the dongle, I need to press the reset button and use nRF Connect. So I am looking at...
hello Nordic
i am working with nrf52840, with zephyr (i am new to zephyr)
i am trying to connect to a low power magnetic sensor (si7210-00-iv)
my i2c sometimes works...
