Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Heelo, i'm trying to use a nordic nrf5340 as a provisioner for the remaining network however i'm getting an error on sending the app-key to the un-provisioned node (I'm using...
Hi, I'm sending SAADC data via BLE. If my SAADC_SAMPLE_RATE is high(e.g. 250ms), the code works perfectly fine. However, if I sample at a fast rate (e.g. 10ms), there will...
Hello,
I posted the following ticket, which has been replied to but it is marked as "Content under review" :
https://devzone.nordicsemi.com/f/nordic-q-a/78575/upgraded...
Why is it so easy to disconnect when upgrading to a few points? The upgrade may be complete
I used SDK 17.0.2's ble_APP_ButtonLess_dFU routine
Do you know? Thank you...
I am trying to build example project in Segger studio but getting error as below............................
Building ‘light_ctl_client_nrf52832_xxAA_s132_7.2.0’ from solution...
Hello everyone,
I am totally new on bluetooth configuration. I have LIS3DH accelerometer from adafruit. and i have nrf51822 bluetooth beacon kit with me. I want to connect...
Respected sir/ madam
I have query regarding the testing of Nordic Semiconductor ASA- Direction Finding Antenna Board (PCA20054) using VNA (Vector Network Analyser). Please...
Hello,
I am testing multi link (1 central - 4 peripheral) bluetooth test with nRF52832 DK module.
I had some disconnect problem with respect to handle, so I changed some...
We want to use nRF52840 SoC as our controller in our custom Board. I have reviewed the product specification document of nrf52840. I have following queries:
Is High Voltage...
The LE Audio specification has published for over a year, but until now there isn't any public progress from Nordic, neither other BLE vendors.
So is there any technical...
Hello, i'm using nRF52833, pca10100.
I would like to connect multiple peripherals by referring to the mulit link example.
First of all, I'm going to try to connect to...
I'm trying to use the I2S peripheral on the nRF5340DK. It looks like the zephyr drivers don't currently support this board, so I need to use the nRFx drivers. I've ported...
Hi everyone,
I have a custom board based on nrf52840, the Fantsel BC840. I have created my custom board, changing assigment of pins for leds, buttons and UART0 on custom_board...
