Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
Hi,
I have a question ,According to the official tutorial，I succeeded BLE OTA DFU in windows system by nrfutil ,however, when I use the nrutil tool to update the firmware...
I have tried to use I2C but it does't work out. nRF9160 doesn't start booting after executing "build and run" and pushing the reset button.
I open secure_boot project...
Hi Nordic team
At sdk connect sample/mqtt_simple, it called lte_lc_init_and_connect() to connect NBIOT or LTE-M.
If this call was not successful, could we read error code...
hi support team,
very strange question from customer
customer set up one interrupt with following code:
void gpio_wakeup_init(void) { uint32_t err_code; if (!nrf_drv_gpiote_is_init...
Hello, I am routing the NRF52840-QIAA chip and wanted to avoid the costly via-in-pad process.
Can I use the following pins for QSPI quad mode?
Also can i leave the RESET...
I have a working set of implementations placed in the 17.0.2 SDK examples directory. The projects use SoftDevice s140 for BLE and flash write operations. I would like to know...
I'm looking to enable the flash protection for an nRF52 application running on Zephyr RTOS:
Basically looking to disable flash reads from the JTAG/SWD interface: Only...
Hello Nordic support,
I would like to understand regarding the status value 'ZB_ZDP_STATUS_NOT_SUPPORTED'.
I have a Zigbee application in which the device type is a Zigbee...
Hi,
I am using NRF52840 DK board. I am using SAADC example program for reading the voltage and SDK 15.3.0 Version.
We have connected the sensor to the adc analog output...
Hello Nordic team,
Our current setup:
nRF52840
nRF SDK v15.00
In our current setup, the steps we take are as following:
Initialize nRF52840 -> BLE fast advertisement...
I am developing a beacon for nRF52832 and can see the beacon in nRF Connect for iOS when using the following setting:
adv_params.properties.type = BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED;...
I am implemeting serialisation using nRF52 as BLE PHY + STM32 micro as host with UART in between them.
I can see there is example for searilastion under "nrf5_SDK_for_Mesh_v5...
Hello
I want to test ncs ota function. b0 module following this link .
ncs1.6.0
borad:nrf52840dk_nrf52840
projece: ncs/zephyr/samples/hello_world
1. b0 + spm test...
Hello Nordic support,
I have a question regarding the Read Attribute response received after sending Read Attribute request. In the read attribute response structure, I...
