Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello, nrf5340 datasheet -> nRF5340_OPS_v0.5
section: 7.1.26.7 Sending custom instructions (Page: 383) 1. we can send an instruction consisting of a one-byte opcode and...
I kind off trying enable TWI in bootloader mode, This is because of following reasons.
Firmware is stuck in bootloader, if somebody removes the Device Battery during...
Hi.
I'm trying to run an application using a custom SPM module in a nRF5340 where I get an error while running it. I'm using nRF Connect SDK. The terminal gives me this...
Hi
I have searched this question on the website before posting this and found that the nRF52 devices support SWD interface (which is peer to peer) and not JTAG (which...
Hello,
I was able to install all tools proposed by the nRF Connect v3.7.0 except the most important : Toolchain manager.
It retruns the following message
running...
Hi, I am interested in using the KMU and I have seen some examples of it here (9160 but similar): https://github.com/einarthorsrud/kmu_sample
and also some docmentation...
Aim: To upgrade the existing Bootloader + Softdeivce + Application package build using nrf_sdk_15 to nrf_sdk_17 on the NRF52840_DK.
Problem: I successfully flashed the secure...
We are using zephyr on that nrf52840 .
Is possible tu run code coverage analisys on that board ? What I have to do ?
Does twister work ?
Best Regards
Novelo G
My technical questions are as follows:
1) I need to upgrade an old iBeacon transmitter we design using the nRF52832 with SDK 11 (Sofdevice s132_nrf52_2.0.0_softdevice.hex...
Hi,
I have develop the Code based on HID_KEYBOARD AND NUS code
here i also need to ADD NVS and DFU to nrf52840 device
1. Pair device address is stored in what manner...
Hello, I'm using SDK 17.0.2. I want the documentation in PDF format. I was unable to generate on PDF document for all documentation. Is there a PDF that I can download?
Hello, I make multii-link peripheral device with 3 BLE HID connections. I extend heap and stack to 16kb and set properties RAM_START=0x20004000 RAM_SIZE=0x3c000. As the base...
