I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hello, I am using SDK 16.0 and mesh SDK 4.2.
We successfully implemented remote provisioning capabilities in our devices' firmware. One thing we are noticing though is that...
Hi,
I am using spis example from "SDK v17.0.2" with slight modification in the code as given below
On the Master end CS pin is pulled low and send 1 byte(0x45) only...
Hello,
I'm using nrf52840 with gcc compiler and SDK15.3. For our firmware update procedure, we use two flash storage instances. One for the transmitted new application and...
Nordic：
We need to do a communication certification, we need NORDIC to provide S112V6.1.1 QDID: 125078 certification report certificate。
thinks
jermi.jin
2021.061...
My CMD.EXE is copied here, it shows the command I'm trying to run, and the output of the program. As you can see, there is no error message.
However, it does not succeed...
Hi there,
I was wondering, do you have a generic "module on PCB" for Nrf9160? Much like ESP32. I would like to skip the design of the RF impedance maching... not my cup...
Hi,
I needed assistance to get the SKY66112-11 FEM working with the Radio Test Example, for certification testing (FCC, CE etc). I am using the NCS 1.5.1 SDK. I have followed...
Howdy ya'll,
I updated nRF Programmer yesterday (1.4.8 -> 1.4.9) and noticed binaries were not flashing to my board anymore. My JLINK is able to read the device's memory...
Hi, I am in need of some guidance. The overall goal is to set up MQTT/TLS communication from end devices in a thread network, via a border router to the AWS cloud. I have...
Hi. I am currently having a nrf52840 custom board and tried to program the sniffer hex file. nRF programmer gave me couldNotOpenDevice (0x4) Lowlevel error: JLINKARM_DLL_ERROR...
Hi all, I have a problem. I'm using a mix of the nrf samples azure_fota and azure_iot_hub connecting to Azure, using certificates X.509. The problem is the expiration date...
Hello everyone.
I have a nRF52840 DK that I am working with.
1.) When I plug into the USB port J2 (MCU interface) I am able to connect to the board program/debug using...
I wrote some code that has multiple custom services where my device acts as GATT Server.
I register the handler for every service (3 in total) with NRF_SDH_BLE_OBSERVER...
Hi,
I am debgging QSPI( type name: IS25LQ040B) in nRF52833, I met " NRFX_ERROR_TIMEOUT ", Could you give me some advice, please?
// Set QSPI pins to pins related to...
