Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
I am using an nRF52 DK and running a modified version of the heart rate collector example from the pc-ble-driver-py repository.
My modified program scans for connectable...
If you can expect the data to be sent or received at random times over UART, does it make sense to suspend the UART in the driver? Is it fine to leave both TX and RX enabled...
We are building a device where nRF9160 acts as a master that runs Zephyr OS (using NRF Connect SDK). Our device has a 2nd communication interface beside the nRF9160 modem...
Good afternoon.
We are engaged on a project that entails the simultaneous, independent development of two separate modules capable of interacting with the BLE stack. ...
Hello,
Im trying to debug my fw using Keil, its running in debug mode and I have RTT printouts, but once softreset occurs debugger doesnt halt it. Device reboots and starts...
fdsa
1.) From the nRF5 SDK I am using the example project for the Adafruit NFC Tag Reader.
2.) Using the project "as-is" I am able to get some basic information about...
Hello there,
I used both the oscilloscope and PPK to measure the current values. But both values are weird.
First, the PPK shows the current as large as 82mA. And...
Couldn't find an appropriate place to put this.
I use the Brave browser.
The ticketing system doesn't seem to work very well with it. Often I find that the options for...
I warry wander this fact.
I have migrated my project from SDK5 to ZEPHYR (nrf connect). Two devices - Central and Peripheral - Long range coded_phy.
I used next samples...
In certain situation when BLE device is disconnected during service discovery process sw can crash in bt_gatt_dm_char_by_uuid due to BUS FAULT (dereference of pointer showing...
I opened an issue on GitHub, but then I noticed that the README says to post issues on DevZone, so here I am.
I'm using the latest version of the Power Profiler app (3.1...
I'm looking at examples\ble_peripheral\ble_app_uart example and I have a couple of questions:
- You explicitly configure the UART inside the main so now once you have the...
Hi Nordic Team,
Since the OTS example is given only for nRF52840 DK and nRF52 DK which uses PCA10056 and PCA10040 respectively. How shall I use this example in my nRF52833...
Hello,
Project Description
in our project we have multiple nRF52DK and one nRF52840DK. We are using the SAADC on the nRF52DK. The SAADC is configured with 4 inputs in...
