Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on automating the FOTA flashing process for 50 PCA10056 (nRF52840 DK) boards using a Python script. The goal is to efficiently flash firmware onto multiple boards...
Long story short, I trusted the datasheet (big mistake) where it says an external crystal is optional. In previous builds, I had an external crystal onboard anyway, so this...
Hi,
I am developing Long Range and Pawr using nrf54l15-dk.
For the Long Range example I refer to E:\NCS\v2.8.0\nrf\samples\bluetooth\central_and_peripheral_hr and peripheral_hr_coded...
Hello again,
I am messing around with connectionless BLE AOA CTE transmission using NCS 2.4. My setup includes the Siliconlabs BRD4191A which is a 4x4 BLE AOA/AOD dual polarized...
Hello,
We are developing a Bluetooth application that uses the Environmental Service to transmit various sensor data. Everything works correctly, but we have noticed an...
When building `nrf/tests/modules/mcuboot/direct_xip` with nRF SDK v2.9.0 for nRF54L15DK the build errors with the following ouput: Is there a fix in the pipeline for this...
Hello
I am doing a bluetooth dongle and I added MCUBOOT with CDC ACM to be able to update my app.
I find that the update takes a lot : 5+ min to update a 200kB application...
I need to send different types of advertisements in my application using NCS 2.9.0 on a nRF52833 and I noticed that I have to increase CONFIG_BT_CTLR_SDC_PERIPHERAL_COUNT...
Thingy:91X V1.0.0 (multiple devices)
NCS 2.6.2, nrf53_connectivity_bridge_v2.0.1
Using the logging of the nRF9151 via the nrf53_connectivity_bridge_v2.0.1 shows on longer...
Hi, We have a network of air quality nodes based on the nrf9160 using Vodacom in South Africa. One morning all the nodes went offline and we discovered that they no longer...
Hi, I am having trouble with the connection of my mesh nodes and my Smartphone over the nRF Mesh App. After flashing my boards ( nRF - 52833, 52840, and 7002), most of the...
HI all,
I'm trying to run the USB next stack-based loopback class with Linux testusb. and only very few of them been passed and everything else been timed out.
I confirmed...
Hello,
We have nRF52832 in production on a custom board. Recently, we created a new functionality with the aim to handle flash more efficiently, and to avoid the case where...
Hi All,
Hardware Details:
nRF-SDK: 2.8
Microcontroller: nRF52840
Setup:
We have an OpenThread (OT) mesh network consisting of approximately 15 devices. All devices...
