Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello,
I'm new to software development so apologies if this is a simple question but I can't find a straightforward answer for nordic connect sdk on vs code.
An IC I...
How can i configure the nrf52840 dongle with DHT-11 sensor such that i am able to use it to send the temperature data via UDP within the Thread Network? I am using the NRF52840...
Hello, I have used this template (ncs-example-application) to start developing my project. I've installed also all the prerequiries to use the application using command line...
I am using the existing nRF Connect SDK (v2.9.0) example of Wi-Fi provisioning using Bluetooth LE ( https://github.com/nrfconnect/sdk-nrf/tree/main/samples/wifi/provisioning...
Hello,
I am currently testing a custom board using the nRF5340QKAA .
Most of the connections are the same as the nRF5340 DK , but the main difference is that I built the...
I dont have Ellisys, but I already install Ellisys Bluetooth Analyzer on my PC.
I got a .btt file in this ticket , but it seems something wrong.
I want some .btt files...
I am using an nRF52840 processor within a Particle Argon IoT module. I am polling a third party BLE peripheral (Shelly relay) for status data once a minute. The data packet...
when i try to use the ddfs to calculate the distance, i can't understand the comments in the README file,
"Zero-distance calibration
*************************
The...
I have followed the guide at https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs-dfu .
(using the option CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU...
After the Matter device is upgraded from version 1.1 to 1.3 via OTA, the Thread connection is functioning normally., but it fails to process chip-tool commands, and chip-tool...
I'm interested in connecting a device to a combination of RAK4631 and RAK5802 using RS485 interface.
I write the code in the Zephyr environment and I cant seem to make it...
"I'm trying to perform DFU using MCUBOOT over Bluetooth. The device enters DFU mode and connects successfully, but when I start the firmware download, I get an error:
Starting...
Hello Nordic Team,
I am currently implementing low-level SPI communication using SDK v2.7.0 and nRF 5340dk . Could you please let me know the name of the IRQ handler for...
