after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi
in communication networks, GPS is often us to sync network elements and to get accurate timing.
with nRF9160 MFW 1.3, "GPS time based configurable IO-pin / pulse" is...
Hi!
I am developing an application that starts and stops gps occasionally. I am running the gps in GPS_NAV_MODE_PERIODIC with a timeout of 100s and an interval of 240s....
Hi,
We are having problems with nRF52840 dongle.
Intermittently pc-ble-driver-py throws the error in the subject when trying to open interface to nRF52840 dongle. After...
I got an average DRx power consumption of 415.03 µA for 2.56s in the Online Power Profiler for LTE. But unable to get the average power consumption of eDRx.
In the following...
Dear Community, I'm trying to use both datasheet-announced I2C interfaces, one as slave and one as master. Datasheet: www.mouser.de/.../BlueNor_BM833A_datasheets-1627946.pdf...
I have a BLE central application (a form of BLE to LTE bridge) which I have no choice but to redesign due to the dismal state of the supply chain. The original device which...
Is there a release plan in place for the release of a pc-ble-driver-py version that supports Python 3.9? I can see on the github that the support has been integrated into...
Hello,
We recently implemented DFU on Android for nRF51 and nRF52 devices using the Android DFU library from GitHub. It works great, and we would like to see if it is possible...
Hello! I'm trying to setup the PPI module so it controls a LED based on an external digital INPUT. It works well while the nrf528232 is ON, except when I call :
nrf_pwr_mgmt_shutdown...
Hello,
I want to use the Nordic UART service from the ble_app_uart example in SDK 17.0.2 (running on nRF52DK) to use directed advertising to send data to a 9160DK client...
Hello,
Looking at the product specification, the nRF5340 system off current is specified at 0.9 uA. Can you please provide an example that I can run on the DK which can...
Hi.
As far as I know the SWD interface can be used to download/upload firmware and make debug, I would like to know if SWD also can make the function of sending and/or receiving...
Hi,
On a dice projet based on NRF52810. Sometime when I plug the battery charger the firmware crash at address 0x18808 and the call stack is empty !
This address is in...
Hello,
Can anyone please share some reference example for implementation code for central device which scan for available device.
I am using nrf52840.
Thank you
I have successfully installed the blinky example app on my new Nordic nrf 52840 Dongle - so that's good! :)
However, some things are not clear to me - so I would like some...
