Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
How much is the temperature characteristic improved by setting CALIBRATE OFFSET for nRF52832? How much does CALIBRATE OFFSET improve the temperature characteristics?
Are...
Hi. In other discussion I have seen pairing/bonding should store all necessary parameters of a discovered service. It's possible then to reconnect to a bonded device without...
Hello,
I have a security issue with a product with nr52840 because if a hacker connect to my device with nrf toolbox for example, when i stop the bluetooth connexion on...
Hello, I've been working with unit tests lately, and got the example unity project to run (from here ). Now I encounter some issues when integrating it into another Zephyr...
I use usb with secure bootloader to flash 52833/840/832 boards. Is there a way to use the nrfjprog --memwr/rd over the usb after a DFU on USB upgrade to new app?
Steps w...
Hello,
I have an analogue audio mic connected to external ADC. The external ADC can give an output of 16bit, 20bits, 24bits and 32 bits I2S data. I have configured to send...
All the SDK health device examples appear to have a rather complicated relation between the BSP buttons and the behavior of the device (advertising, connected, etc.) which...
Hi Everyone,
I am having some trouble on nrf5380 PDK. I can not connect it to my PC.
I attached photo of nrfconnect.
There were 3 serial ports but I have used just one...
when using the TIMER, I set the TIMER's time_ticks=53328 which means that every 3.33ms, the TIMER will call its callback function and start ADC sample. However, when I use...
Hi.
We are evualuating and testing NRF9160 DK and after a while testing and reading different threads of the forum I know the mode GPS + LTE in the nrf9160 only work in...
Hi. I'm using external board with nRF52832 and GPS. (SDK15.0.0)
I used ble_app_uart example and succeed in receive data in my nRF UART v2.0 app.
I got this kind of data...
Dear all, Im experiencing the following error that pops out on RTT console during the first few lines of main():
I understand the definition here: https://infocenter.nordicsemi...
This is my code:
This is the results of the logs in the code:
<info> app: tx buffer length = 8 <info> app: AA <info> app: FF <info> app: 10 <info> app: 08 <info> app...
