Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Dear Nordic
Q1.
We tried new nrf9151 IC at custom board.
IC version: nrf9151 AEA (Engineering B)
Firmware: ncs2.7.0 Serial LTE modem application + mfw_nrf91x1_2.0...
hi,
When verifying the modem upgrade, if the network type is set to support both Cat-M and NB (AT%XSYSTEMMODE=1,1,0,0), the actual network that connects is NB, and the modem...
I have 3 nrf boards connected. 2x nrf52832 and 1x nrf5340.
esb_tx is running on nrf52832(682782977) esb_rx is running on nrf52832(682497942) & nrf5340(1050025410)
west...
Hello
I have a custom nrf52840 board with an external 1MB NOR flash
The app uses MCUboot for DFU
I know I can define the external flash in the pm_static.yml for the...
We are currently working with the nRF52832 Development Kit and are aiming to interface an ISO15693 NFC reader using the PN7150 NFC module. We intend to communicate with the...
Are there any serial commands that I can use to control some the functionalities of the board. My task is to use the dk with a windows app (UWP, C#), I want to start stop...
I tested it on the lzma example (ncs\v2.8.0\nrf\tests\subsys\nrf_compress\decompression\lzma),on the Cmakelist.txt code
generate_inc_file_for_target(
app
${ZEPHYR_NRFXLIB_MODULE_DIR...
We have a production system running a modified asset_tracker_v2. Things are basically running fine but there is question with downlink and FOTA operations. We publish a JSON...
I am trying to get mcuboot working on a custom board. on version 2.7.0 sdk, But the board is not found.
I have simplified it to a minimal version like so (my folder can...
I am evaluating external flash on nRF5340DK. When I'm doing appcore DFU from external flash so that mcuboot_secondary and settings_storage are located on external flash, everything...
Hello!
I am returning to software development for a BLE Mesh project on the NRF52840 after being focused on the hardware development for several months. I see that NCS is...
Hello
I am evaluating Wi-Fi location using the nRF7000 and nRF9160.
For the initial test, I used the nRF7002 Expansion Board. I soldered wires to it and connected them...
What would be the certification cost for developing small volume Zigbee or Matter+Thread applications using nRF modules and nRF Connect SDK? Is this eligible to certify via...
Hi experts,
I followed the instructions the Readme file described. It almost works well. But I still found two issues:
the Startup time is too long when pressing the...
