I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
I have added shell console and its support into my nrf54l15 device and it worked well like below.
But now I want to use a python script to run this "bt" shell command...
Hi
I want to use BLE to send out realtime videos, and I found there is a nrf70-wifi-ble-image-transfer-demo given by nordic. Could you show me what is the BLE Camear App...
trying to build matter sample example light_bulb but getting error :
nRF connect sdk v2.9.0 & tool chain v2.9.0 using
board nrf21540dk/nrf52840
following are the...
NCS 2.7.0 with Toolchain 2.7.0
I'm working on an out of tree application derived from the example application project.
I'm using sysbuild with MCUBOOT.
The processor...
Hello, we are using the NRF52810-QCAA in LDO configuration. On reference design, there is an NC decoupling capacitor on DEC2 pin.
Is it possible to completely remove it...
Hi,
Not sure if it's a zephyr issue or a LVGL issue, so I hope I'm at the right place.
I use an 1.54 eink display with the SSD1681 driver, and LVGL. Everything goes well...
Hi Nordic,
Board:nRF54L15 DK
Code Base:peripheral_uart
Issue: Added Zephyr NVS Flash support but encountered error -22 from nvs_mount(&fs). Additionally, data cannot...
Hi everyone,
I'm working on the nrf54l15 with the nrf sdk v9.0.0 wihch I assume integrate matter version 1.4. I'm using the google nest max as a thread border router....
I am developing on a custom nRF5340 board, but I encountered a BLE-related error. To troubleshoot, I built and flashed the basic example peripheral_uart , but the following...
Hi,
We are working with nrf53-DK evaluation board, and we are using P1.02\P1.03 pins for I2C communication.
We wanted to connect a 5V I2C slave on these lines can we connect...
Hello!
I am using an nRF Connect SDK V2.9.0 with a nrf54l15. I want to set up a project with a custom board. I want to add DFU in the future, so there must be MCUboot bootloader...
Hi everyone,
I'm currently working on a low-power application and aiming to minimize sleep current as much as possible.
Thanks to some great advice I've found on this...
Hey so I am making a capstone project with Drapers lab from University of Massachusetts Lowell and one of the requirements is to create an friendly end-user GUI instead of...
I want to confirm these questions,hope someone can give me some explaination.
1) RADIO has it's own kernal which is some kind of MCU.
I have looked through some doc on...
