I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello all, I've just bought nRF9151 DK and went with Quick Start. I loaded nRF Cloud multi-service sample. Sample runs and connect to network. Sometimes it sends data (location...
I am following the Cellular IoT Fundamentals course and trying to get my nRF9151-DK set up as a device in the nRF cloud. ( https://academy.nordicsemi.com/courses/cellular...
Hi
I have two nRF54L15 DK boards (PCA10156).
Both are behaving the same way right now.
.......................................
ONE: Using nRFConnect in VSCode...
Hi,
I am currently developing a heart rate strap using SDK 17.1.0 and the S312 SoftDevice with the nRF52805. I have noticed an issue: when I connect the heart rate strap...
Hi
I'm using the periodic_adv_conn example from SDK 3.0.0. In the request_cb function, the bt_le_per_adv_set_subevent_data function is used to load data for future subevents...
Hi,
I want to use the die temperature sensor in the nRF54L chipset and am wondering why the definition have changed slightly compared to previous chipsets. In the SoC device...
How precise do the trace antenna dimensions have to be? Given that the datasheet for the nRF54L15 only has a reference layout up to and including the matching network, but...
Hi Nordic:
We currently need to provide the RoHS and MSDS test certificates for our product's NRF52820QDAA-R. I checked the certificates on Nordic's official website, but...
While testing, I encountered the following error after flashing the modem firmware and running the DECT example:
<err> nrf_modem: Modem has crashed, reason 0xfff, PC: 0x0...
Greetings,
I want to change Device name on Advertising. Is that possible? I am using nrfSDk52832, I want when some state of Switch is change, to change advertising name...
I am new to this device, so please bear with me during the inevitable simple misunderstandings! I am scanning for bluetooth devices and getting sensible numbers of devices...
Hi, I have a custom board with an ISP1807 onboard. We'd like to optimize the production process, especially the programming process. We currently use the nrf52840 dk board...
I have a small demo, based on the hello world example, where I have also enabled gpio_keys. I can run this on the nRF52-DK, nRF54-DK but when I come to run it on my custom...
I have seen a few posts including:
Change advertised name (Bluetooth) - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi.com)
NCS bt_set_name() - Nordic Q&A...
