Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hello,
I am new to Zephyr and I am trying to figure out the best way to set up a new project for a nRF91 modem. Ideally, the project should allow patching of the nRF Connect...
Dear All,
I am working on a project using the nRF52810 with the secure bootloader configuration from the Nordic SDK 17.0.2 . Specifically, we are using the example:
....
I've setup my development environment using the 'application' structure. https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/develop/application/index.html#zephyr_workspace_application...
With the nRF52840 we used RSSISTART to start the sampling of the RSSI and got a RSSIEND event when we could read the RSSISAMPLE register.
The radio on the nRF54L doesn't...
Hello,
I am working with the Multi-Service sample on the 9161dk and also a custom 9151 board.
The multi-service sample compiled option works great but the samples, when...
Greetings.
Background:
We have a custom device, that uses the nRF9160 as a Modem, with Modem OS 1.3.4 and a sightly modified "Serial LTE Modem" FW. One of our Devices...
I'm trying to send simple packets using the radio peripheral.
In my test scenario I have the following conditions:
The HFXO is started and is running the whole time...
hi
the lengths of the this track is important?
if i decrease this length, how i can set antenna parameters?
another question: what is the R1 =0 ohm resistor and N...
I am using Fanstel evaluation board with BT805 attached.
I got an example project - ble to uart.
I was able to build the project with Segger V5.42 (any later verisons...
Dear all,
I tried this example regarding async SPI:
https://github.com/too1/ncs-spi-master-slave-example
I also wrote overlay for this example to work on nrf52840...
Hi, we have a custom nRF5340 based device. Has NISB and MCUBoot Enabled. It takes about 2.5 seconds to get into the application and BLE advertisement to start. Wanted to know...
Hello,
I´m trying to send a paket of databytes. For some reasons I need to send it byte by byte (that´s not changeable).
I have inited the uarte with a handler:
nrfx_uarte_init...
I am using the nPM PowerUp utility along with an nPM1300 development kit. The software provides options for configuring the soft-start current of the load switches. However...
Hi all,
I searched nRF54L PRELIMINARY DATASHEET v0.8 and found
9.1.1.2 DLPIDR: TINSTANCE field description reads " This value is set by the UICR.TINSTANCE register. "...
