I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Hi folks,
I'm trying to write a program to check out a pair of nRF24L01p modules talking to each other, and I'm a bit confused about two aspects of initialisation:
...
We are using your nRF24l01+ chip in one of our products. we are using 1 nRF as receiver and 5 nRF's as transmitters.
While trying to use the chip with multiciever configuration...
Using SDK13 - I would like to use the fds/fstorage libraries, but I'm told that "The experimental label is due to lacking test coverage for the two modules". here
At the...
Hi,
I've been suffering with detection of writing to cccd to enable notifications. The S132 (nRF5_SDK_13.0.0_04a0bfd + s132_nrf52_4.0.2_softdevice) never fires BLE_GATTS_EVT_WRITE...
Hello, I'm migrating a project from nrf51 to nrf52, and there is this function:
uint32_t dfu_init(void)
{
m_cmd_handler = *((bl_if_cmd_handler_t*) (0x20000000 + ((uint32_t...
Hi,I use demo project in
nRF5_SDK_12.1.0_0d23e2a\examples\peripheral\saadc\pca10040\blank\arm5_no_packs\saadc_pca10040.uvprojx.
I made the following changes:
1.add...
Hi all,
what is the most correct way to delete the bonding information when the client and peripheral are connect.
Delete_peers
Wait the QUEUE_EVENT_PEER_DELETE_SUCCESSED...
Hi,
I have an nRF52832 sending data to a central device. At the central side I am testing two tablets (separately). One is a Samsung Galaxy Tab A 2016 10" and another one...
FDS error in FDS_VIRTUAL_PAGE_SIZE 1024 ?? (NRF51)
github.com/.../nRF52-fds-example
If I use FDS_VIRTUAL_PAGES 3 , FDS_VIRTUAL_PAGE_SIZE 1024 , then there comes FDS_ERR_BUSY...
HI,
I want to snifer BLE data using nRF51 dongle and ble-sniffer_win_1.0.1.exe,but when I plugin the dongle on my pc,then running ble-sniffer_win_1.0.1.exe ,it can't scan...
For my application I use a RTC. For now without SD and based on SDK 11.0. Later I will implement it in an application with BLE. My device is a Raytac module with a nRF52832...
I see some interesting phenomena on the power profiler (with nRF52840) that would need some help to explain. I am using the ble_app_uart code from ble_peripheral folder in...
I press the debug command for my program
Then I press the run the command
Here is the function of the run command
Continues executing the program until
...
