I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
I'm currently working on a custom board based on the nRF52840 , using SoftDevice S140 v7.0.1 and nRF5 SDK v16.0.1 . I’ve integrated the BLE Buttonless DFU example ( examples...
Hi, last year the name of the Zephyr module "TraceRecorderSource" was changed to "percepio". In January a PR was accepted that updated the SDK's allow-list (west.yml).
We...
Good morning,
In my application (SDK v 2.8.0) I would like to disable/enable runtime the advertising for the mesh provisioning. The inizialization of the mesh stack works...
Hello , I have a problem on angle of arrival application to see switching nrf52833 board
I use nrf52833 dev board. I use 2.0.0 as sdk version. I use nrf/samples/Bluetooth...
I would like to know the recommended battery part that is suggested by nordic to work with the nrf5340 Audio DK. I saw some blogposts where it was mentioned that a 3.7V 1500mah...
Dear nordicsemi,
In our application, we need obtain the number of input edges,but we always get a incorrected result in a long-time testing situation (2-3 hours), and this...
Hi,
I would like your support in reviewing and helping define the correct configuration for the NPM1300 charger in our application.
Here is the current configuration we...
working with a nrf52833, soft device 140.
I am trying to setup a whitelist with a known addresses before I start scanning. I am calling the following code before my main...
I am trying to find the reference manual and specification of the S130 SoftDevice (2.0.1). I can't seem to find it in the info center or the your docs page. Am I missing it...
Hello, I'm developing a BLE Central application using the nRF52 SDK. The central connects to multiple peripheral devices (nRF52832), each sending 6-byte ADXL345 accelerometer...
Hello,
I am trying to get a custom board working with NOR Flash chip but I am having issues getting the flash chip "ready". I am running the sample application "spi-flash...
Hello,
I am using nRF54l15 and nRF Connect SDK v2.9.0
I need to know if there is any way to disable the cfg_changed callback at runtime. I want it to be called in case...
Hi,
We recently purchased two Thingy:91X devices and are trying to run the nRF Cloud Multi-Service sample on the nRF9151 SiP onboard. To provision the Thingy:91X for communication...
I had to modify the modem_cellular.c file driver in Zephyr to make it work for a SIMCOM modem. I know I could try getting a PR to Zephyr approved but it'll take some time...
Hello,
I'm trying to evaluate a FW development for several features of BLE used simultaneously. I need a BLE Peripheral for mobile phone connection (advertise only once...
