Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
Keep hitting my head on this inconvenient workflow.
Edit build config
Select target custom board
Build config
All OK
Edit config again
Target board has been...
I have used the Programmer previously with success. I am attempting to program the Dongle (10059) with a slightly modified version of ble_nusc_usb_dongle. Although it claims...
Hello Team,
I have flashed the bap_unicast_server bluetooth sample on my nRF5340 Audio DK. No build or flash errors. When I connect to my phone it connects properly. I'm...
I'm working on a project involving a USB dongle based on the nRF52840 SDK-2.9.1, which needs to communicate with a sensor (also an nRF52840) and transmit data via USB to PC...
Hello Nordic team, For the ( POC), I configured ADC channel 1 and interfaced a potentiometer to pin P1.14. The ADC was set up accordingly to read raw value from the potentiometer...
We are in process to certified a product using the nrf52832. While testing the certification team find an offset greater than 20 ppm, like in the following scree shot:
...
Hi team,
I have to create a program which sends messages from one dongle to another. Now I have ported radio transmit and receive + USB CDC ACM programs for two 52840 dongles...
Hello,
I have experienced some softdevice hardfault in my multiprotocol application. I use https://github.com/NordicSemiconductor/nRF-IEEE-802.15.4-radio-driver/wiki with...
Hello,
My application, running on nRF52840 with SDK15.2, needs to detect the reset source from System OFF state. However, when using the BLE Secure DFU Bootloader, it always...
Hello,
I use nRF5SDK160098a08e2 SDK version, on ubuntu 16.04.
I use pca10056 (nrf52840 dev-kit).
I want to run cc310 example located at ./examples/crypto/nrf_cc310...
hello,
We have a product in production using nRF51422 and we are scaling up volume in a new manufacturing facility.
The functional tester stations require use of Master...
Hi!
Is there an example of how to use BLE_GAP_CONN_SEC_SET_MODE_LESC_WITH_MITM?
I cannot find one and I am having a hard time understanding what I need to do to make...
Hi,
I'm trying to use the pc-ble-driver "nrf-ble-driver-4.1.1-win_x86_32" to communicate with our nRF52-based embedded product. The fact that the PC and embedded implementations...
Hi,
I am using NRF52832 with secure bootloader to OTA my application in the field using Dual Bank updates and everything is working fine. In my application, I am using FDS...
Hi,
I need to use external eeprom memory AT24C256. I have not found any example for nrf52, so I started with migration existing arduino code to Nordic´s. Here is the Arduino...
Hey,
I am working on NRF51822, S130 softdevice integrating security, I have used the GLS as a reference for security implementation.
I have a use case in which I am...
I have both ble_app_uart_c and ble_app_uart they are automatically connected to each other if they are on. my question is ble_app_uart_c supports one to many or not? if it...
I am developing using pc-ble-driver-js and nrf52840 dongle.
We know that nrf's development tools (nrf connect ...) are being developed using an electron framework,
and...
We are using SDK 15.2.0 and softdevice s132 v6.10. we want to use the concurrent feature for broadcaster and observer. we wanted to just confirm that this feature is reliable...
Hi, I don't understand enough about electrical, but i found that a little piece of component in my nRF52840 dongle was gone.
It was something in this position:
It was...
