The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
Hi,
I'm using SDK v17.0.2 on my nRF52840-based board. I have implemented buttonless secure OTA reflash and it generally works. When I get the NRF_PWR_MGMT_EVT_PREPARE_DFU...
We have some dev code where the workflow is as follows:
1. an engineering version of firmware is loadded to target. The target is erased then programmed in the normal way...
Hello,
I am using nRF9160 dk for prepare a program to I2C scanning for address. Can any one give a guide for start this task. Moreover, I am using Zephyr kernel on nRF9160dk...
Hello,
I want to read external accelerometer on nrf9160dk using I2C. But when I connect SDA and SCL pins of sensor to nrf91, there is no output.
The Code is:
When...
I am trying to set the UUID definitions for the Windows Application Bluetooth Low Energy 3.0.0. The only doc availible is for v2.3.1.
I tried to follow the following steps...
I'm using nRF SDK 12.2.0 and the corresponding soft device. I control a I2C slave for which I use the TWI peripheral through the driver implemented in nrf_drv_twi.c. It happens...
Hi,
I trying to enable Hardware Key for mcuboot.
I do the following at mcuboot.conf
CONFIG_BOOT_HW_KEY =y
But I got the following error:
Do I miss something...
Hello, I test SAADC on nRF52810, when I short gound to AIN0, the output is 0 normally, and when I add nothing to Pin I0(AIN0), the output is around 1056(Figure0), however...
I'm using nrf52833 on custom board.
And I need to using RESET pin to GPIO for battery charging detection.
I found CONFIG_GPIO_AS_PINRESET is configuration RESET pin...
Hi,
This may be a basic question. I'm using NRF52840 DK and I'm trying to print some logs from timer callback function, however I havent been successful so far. Here is...
Hi all,
I am using nrf52840 with zephyr
The below link puts device in bootloader mode but with pressing button
I want to do it without pressing button
https://devzone...
Hi All,
I just recently updated to a Mac w/ Apple M1 silicon and am struggling to get my (previously working) scripts to work w/o error.
Specifically, this command/error...
I got an nrf5340-dk development kit. And when I connected it to the computer it was discovered by the computer. But, I could not either connect to it or program it.
I noticed...
