The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I have a 52840-DK (PCA10056) connected over USB on Windows 10. I am using IAR and can build and run demos from EW in this configuration but am having no success with nrfConnect...
I am working on a project on the nrf52832 board using mesh SDK v3.2.0 and SDK v15.3. I am trying to troubleshoot an issue with the publish process for BLE mesh, but I am not...
Testing DFU with IOS version of nRF connect. I am able to save my image to the IPad with Itunes. I can select the file and then start the DFU process.
Process completes...
I am trying to setup a VM (Ubuntu 19.04) that has the complete setup for NRF91 development. I have been following the instructions in the nrfConnect 3.2.0 - getting Started...
Dear Support,
In our new project, we have 8 signal LED diodes attached to nrf52832, they are all sinking current:
3x GREEN 0.8mA (P0.16, P0.17, P0.18)
1x RED 3.3mA...
I am trying to setup a VM (Ubuntu 19.04) that has the complete setup for NRF91 development. I have been following the instructions in the nrfConnect 3.2.0 - getting Started...
Hi,
I'm using SDK 15.2. I flashed the dtm firmware on the BLE chip. How can I test its working before sending it to the certifier? I have nrfgo studio & I'm able to start...
Hi Team
We are able to flash nRF52840 based LE Module using nRF52840 DK successfully.
But we would like to know if nRF52 DK also can be used to flash/program this nRF52840...
Hello,
SDK:15.3
If not pair with moblic phone, spi is normal
And obile phone pair 52811 to send data, that also normal
But I want to integrate, then 52811 is NRF_BREAKPOINT_COND...
Hi all:
For SDK15.3, if I want to change 32.768Khz to internal LF clock, Should I enable the CLOCK_CONFIG_LF_CAL_ENABLED of "sdk_config.h" ?
if I disable CLOCK_CONFIG_LF_CAL_ENABLED...
trying to implement an external interrupt with both edge triggered. I wanted to try first pin_change_int example in sdk 15.3.0 but it is not compiling. I didn't do any change...
Need to communicat between nRF52810 and nRF24L01. nRF24L01 is standard module from Nordic. we are using nRF52 development kit and using Segger Embedded Studio (as suggested...
