We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi all.
I did a layout with NFC antenna with a nRF52832 chip.
In the schematic (suggesten on datasheet) I have antenna coil with 2 capacitors to ground.
Drawing...
Hello everyone.
I would like to set-up a mesh network of Thingy:52 devices and an nRF52840, which would help me communicate from the an external stimulus to the phone, via...
I have an application where the nrf52840 dongle is hooked to a sensor. The sensor drives a pin high, the mcu grabs data from the FIFO (SPI) and puts it in a buffer. So far...
Hi Team,
We need to use Flash as EEPROM and we have the following queries,
1. How much maximum size of Flash can be configured/emulated as EEPROM/NVM?
2. Whether below...
When using the serial_lte_modem application on a custom nrf9160 board I have discovered that I get nothing out of the UART unless I pull VEN low and then release it (reset...
Hi guys,
I am using Zephyr RTOS and trying to enable my device to send the voltage data via BLE. I use two nRF52832 boards, one of them is peripheral for which I use peripheral_ht...
Hi Team,
We need to know the what kind of security level available in Nordic nRF52X(nRF52833).
Secure boot support and where the 128bit AES keys are stored and accessed...
Hi Team,
We are going to use nRF52833 chip-set and we need the below information based on this input we will decide our chip-set.Kindly update your support.
1. What is...
Hi ,
The size of the boot loader partition 24KB is fixed for the lifetime of the device or it can be extended, as we have some feature to add like firmware update.
Firmware...
Hello,
I read through the datasheet of the nRF85832 to understand the peripherals a little bit better, but I got stuck while looking through the register overview (in this...
I am using NCS-Zephyr, Zephyr version 2.3.0-rc1. If you need to know the NCS version too, please can you include how I can find this?
When I do west flash normally (which...
Hi Team,
We have requirement for firmware update over Ethernet [ external Ethernet ENC28J60 module interfaced over SPI] 1. Is bootloader customizable for adding SPI driver...
Hi all,
I'm working on a project which I started from the multiperipheral example. I am using SDK 15.3.0 for this. I am developing the software on the nrf52840 DK using...
Start SEGGER Embedded Studio by clicking Open IDE //Successfully installed, what means Open IDE ? ? ?
Select File → Open nRF Connect SDK Project… //it just dont appear in...
