Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi, I'm trying to measure the current of my nRF9160 DK (PCA10090 v0.8.2) and have some problems. In respect to the following thread (https://devzone.nordicsemi.com/f/nordic...
Hello. Project im developing requires low power wireless encoder. NRF52832 is a really impressive chip that handles everything i need within 40uA. But I've got problem with...
hi, we delevoppe a card with a module which is use your nRF52832 IC. I check in your document information relative to IO hardware, but i didn't find any information concerning...
I am writing some code for a customer using the nrf52840.
The Softdevice asserts immediately after a call to nrf_fstorage_write().
The write address is OK, alignment...
whenever I use nrf connect desktop app in my Linux system for power profilling.
The power profiling kit doesn't start and keeps on giving the same error
There are similar...
Hello team, I'm working on system development using Mesh SDK and I have some questions so please let me know. ############### Development environment IDE : Segger Embedded...
I was able to create 2 times, Timer 1 and Timer 2.
They work when they run separately, but one stops when I try to use both of them.
I need simultaneously running two...
Please confirm the following is correct for nRF52840 (per PS v1.1)
1. The firmware doesn't have to enable internal pull-up when the pin reset is configured (it's done automatically...
Hi,
I am developing a solution with zigbee (nRF52840).
I want some end device is joined to specific router.
In the documents, if end device find more than one router...
Hi, Everyone.
I'm trying to connect nRF52 DK Board to J-link base tool.
But I can't connect.
Wires between nRF52 B/D and J-link base tool are conneted below.
nRF52...
Hi,
I am new in this area. I wanted to use the detect "signal" but it doesn't work as protected. This is my main :
I just try to detect when the detect signal is HIGH...
Hello,
i tried the getting started procedure with the NRF9160DK demo board but I cannot finish the whole procedure.
After activating the iBasis eSIM, I turn on the...
It's may be strange enough, but i can't see the clear answer on this question. What is the limitations for pin function maping? I need to understand which pins i can use for...
Hi,
I am surveying the zigbee example for my project.
In my project, coordinator has to permit or reject certain end device/router.
I have searched following articles...
Hi,
We want to send our board for Radio testing and the facility needs a test setup. Radio test example could work perfectly for us but unfortunately, I am unable to use...
