Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
hi,
I used nRF52932QFAA ,SDK14.2 uart bootloader.it works well with softdevice loader 5.0.0.But when I download my app(without softdevice),it cannot work.
Flash composed...
Hello Noric Dev Zone members,
we are looking for a Firmware developer supporting us in bringing Hyko to our customers.
What we are working on is making energy heroes in...
It would be very helpful to hear of others experiences getting these licenses, also I would like to find out if anyone has any advice of anything to be included or excluded...
I wanna implement this code for the app inventor, but there was several problem here. I can't use array or index for developing my trapezoidal method.. like this..
code...
Hello,
We are looking for a developer a single task project. We need to provide all of our developers with the same development environment, so we are looking for someone...
Question 1:
The nRF9160 datasheet V2.0 claims the sensitivity is: CATM=-108dBm (mid band); NBIOT=-114dBm (mid band).
However when the unit connects, we get a printout...
So in the MQTT example the following function is used to write the CA certificate to the modem so a TLS connection can be setup.
In our code/TLS setup we want to use Client...
Sorry this is an urgent request and we could not find much information on the internet about this module. We have a tight schedule so it might be a good idea to post here...
Hi, Hope your are well, i am currently in the final part of my project where i am SPI Gyroscope float data from one nordic nrf52dk (S132) to another such that i can analyize...
I am running read str 0x3e000 12 via UART line but there is nothing which gets printed on the terminal.
Even if i write some hex value to a particular flash memory location...
Hi there,
I have set up the nRF2427 with the nRFgo Starter Kit motherboard (nRF6700). The motherboard is recognized and I have all of the 2.4GHz options available. I would...
Hello,
I am working on the nrf52832 board with SDK16.
I am using a custom BLE example.
My TWI and BLE code work ok individually but when I integrate them it does not...
Using S132 v7.2, I'm getting a hard fault at PC 0x00015810 (I see the flag set in SEGGER, and the console outputs a SOFTDEVICE ASSERT FAILED error) that I'm working on manually...
Hi,
The 'nRF Connect' SDK (v1.4.99-dev1) sample OpenThread CLI is programmed to receive 'ot' commands from UART console. When configured with multi-protocol support, the...
Hello,
I have a problem that sometimes the supl_client_session() function halts the system by not finishing and ending the session while getting the timeout expired SUPL...
Hi
I can't find fwid for sd132 7.2
|s132_nrf52_5.0.0|0x9D| |s132_nrf52_5.1.0|0xA5| |s132_nrf52_6.0.0|0xA8| |s132_nrf52_6.1.0|0xAF| |s132_nrf52_6.1.1|0xB7| |s132_nrf52_7...
Hi there,
Our team is developing an application based on the nRF5340-DK - we are developing on the DK while our hardware is in transit. Our schematic largely follows the...
Hello, I use the internal crystal, the application in my board runs normally and it shows the board is in fast advertising state. However, I can't find bluetooth signal through...
I'm running the Zephyr hci_usb sample on a nRF52833DK to see if I can use it as a Bluetooth dongle on my Ubuntu dev machine. It appears as /dev/ttyACM0, so:
sudo btmon ...
Dear Nordic,
I have a BLE mesh product that is in pre-production. The mesh gateway is composed of an nRF9160 and nRF52840 with a UART link connecting them. The nRF52840...
