Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi.
I'm enabling a BLE sniffer on rRF52840 DK to listen to packets between Windows and the other one BLE board, I can get advertising packets but Wireshark can't switch...
Our mission is prevention the increasing cases of missing persons. We wish to design a positioning device which can track the location of our users for their safety.
...
How we can get to know about the ADC sampling is done. On the basis of the sampling done i want to do furture opration like the stop sampling,Continues sampling. How i can...
Dear Experts,
I am planing to use 52810 to connect to a BLE speaker to play a short 'music'. I checked the BLE services provided in SDK:nRF5_SDK_17.0.2... but seems none...
Hi
I'm developing nRF52832.
I have a question about SPI communication.(\nRF5_SDK_17.0.0\examples\peripheral\spi I don't understand, so I ask questions.)
I want to read...
We plan to use nRF52840 in our new project. But the application is likely to be larger than 500 Kbytes
So we are going to use the only one Bank flash for DFU as in following...
We are thinking of making changes to the QIAA aQFN73 circuit configuration from 5 to 4 and use the REG0 DC/DC. VDDH will be connected to a single-cell Li-Ion battery (3~4...
hi, i am working with nrf52840 and need a stand alone qspi peripheral in the project. what is the straight forward way to get qspi into the code up and running without involving...
Håkon Alseth was helping me with this: https://devzone.nordicsemi.com/f/nordic-q-a/83126/hard-fault-using-twi_scanner-example I accidentally clicked "verify answer" when trying...
Hi,
I have the Power Profiler Kit PCA63511 used on top of the dev kit PCA10040. I am trying to measure the power consumption of my custom hardware implementing nrf52832...
Hello,
I am using nrf52840, SDK 17.0.2, softdevice s140 and also implemented OTA DFU in my application.
I want to save some data lets say admin code in flash. Once I burn...
Hello,
I'm having difficulty getting the GPIO set up in a way that behaves predictably on the nRF9160 DK. As far as I understand it, the nRF52840 is what controls the GPIO...
Hi All! My question is that while using coded PHY is it possible to enable the ACK? In case no ACK receives then retransmission of the same packet to the receiver. Thanks...
I am trying to measure the frequency of the square wave on the ARDUINO_6_PIN on the NRF52840 Dev Kit. It seems like it works well until the square wave goes above 2MHz. Is...
