Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Uisng pca10040 and SDk16.0.0 + Segger
I built and ran the GPIOTE example so I could experiment.
I want to toggle a gpio once only and then stop and I need to know when...
Hi,
Iam looking for very simple low cost wireless module which supports at least 500meters range ,please suggest a module.
I dont need lora module apart from this please...
I have latest SDK, which is nRF SDK 16.00. I have noticed that not all the examples are available for PCA 10100.
So my question is what is the difference between the PCA...
Hi,
I have compilation error to use SPI.
Checking project status Building ‘ble_app_beacon_pca10056_s140’ from solution ‘ble_app_beacon_pca10056_s140’ in configuration...
Hi,
I am trying to get the nRF-IEEE-802.15.4-radio-driver found at GitHub to run on my nRF52840 DK.
Does anyone have a check list or can explain how to link the files...
Hello,
I'm wanting to start a project with the NRF52840 DK in Segger Embedded Studio. I went through almost all of the tutorials and set up the SDK.... etc but I have...
hello.
I used 52840 act as center device.whose RX TX connected to my another MCU(MTK7688 UART). This is a IoT-GateWay. now I want to upgrade the 52840 application. BUT,...
Hi
Two years ago our device was tested using nRFgo Studio 1.21.2.10 Direct Test Mode.
How can I know if the nRFgo software used BLE 4.2 or 5.0 during the tests? The only...
Hello,
We are making a custom application where we have several ble-mesh server nodes (nRF52832), and one of them connects to an Android app, acting as a proxy. The app...
Hi All,
I want explore BLE5 extended advertisement with nRF52832.
Using "ble_peripheral\ble_app_blinky" code from SDK16.0.0, facing " NRF_ERROR_INVALID_PARAM (7)" error...
Hi, I ported the TimeSync example devzone.nordicsemi.com/.../wireless-timer-synchronization-among-nrf5-devices to the current SDK 16.0.0 and S140_nrf52_7.0.1_softdevice. But...
I am unable to set the PA/LNA Mode on NRF52832 using SDK 14.2 ( Soft Device Version S132 5.0 ) using the Fansttel BT832X SoC.
i have used the exact function on the below...
There is the nRF52840 specifications sheet at the reference circuitry there is a pin 74 that is indicated as ground, what is this? 74 does not seem to line up with the method...
I don't know if this something I'm doing wrong, a Segger stupidity, or something else. I'm using SES and copied the examples/ble_central/ble_app_blink_c project to another...
