Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi Everyone,
I am using nRF52832 with SDK v14.2 and SD v5.0.0 on a custom chip.
Recently i included DFU support to our application. It turns out that secure bootloader...
Hi, I'm new to nRF52480 and Nordic SDK. It is first time for me when SDK has one big config file sdk_config.h. I started playing with examples (LEDs, serial I2C) and get it...
I am developing a PCB that contains this schematic, I can run the sw code on the nrf52832 and use the pinout, but I can't connect to nrf52832 via ble communication. I think...
Hi. My product uses nRF52840 as a beacon transmitting every 3 seconds at max power of +8dBm fed to an antenna of gain 2dBi. Is SAR testing needed for my product? Product is...
Hi,
In our application Csense driver is used.As it can be implemented using COMP and SAADC,due to mentioned limitations for COMP we opted to use SAADC.Only AIN7 is used...
Hello, I have a time critical project that requires a unique service routine, thus a specific 128 bit UUID. I am following the tutorial on custom services but it does not...
I need to make something like this and need that baudrate which are configurated in smartphone BLE app that this value be and on NRF528XX uart baudrate.
For example when...
What is the recommended way to flash firmware onto the stand-alone microcontroller. I have never dealt with a stand-alone microcontroller before.
Vineet Nadella
I am trying to get buttnless DFU working on the NRF52832_XXAB which only has 256K Flash and 32K RAM.
I have buttonless DFU working on the nRF52 DK which has the larger part...
The above is the waveform of data pin and chip selection pin.（The yellow waveform is the data pin waveform. The blue waveform is the chip selection pin waveform. And chip...
Below is a picture of advertising event current waveform:
The TWI current consumption is upto 2mA, I change the peripheral from TWIM to TWI, the current is exactly the...
We are developping an application using an NRF52840, Based on nRF5 SDK for Thread and Zigbee V3.0.0
Running S140 softdevice
We are using BLE advertizements and Openthread...
I followed the guide Configuring and performing DFU over Mesh ,old firmware was examples\dfu\build\dfu_nrf52832_xxAA_s132_6.1.1_Debug\dfu_nrf52832_xxAA_s132_6.1.1.hex,new...
