I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
Hello,
I am using NCS v2.8.0.
In this, when I configured the application to use OOB legacy pairing only mode, the build process failed.
Following is the configuration...
In our firmware we use BLE together with ESB using the MPSL timeslot API, with the implementation inspired by this example: https://github.com/too1/ncs-esb-ble-mpsl-demo However...
Hi,
I am trying the sample code in this regard. I have changed the I2C pins in the overllay file and bme register address to 0x77 as follows. It seems working but I have...
I am using nRF52840/nRF52833 (raytac module, original board). With the current nRF Connect SDK, is it possible to disable NFC and use ports (P0.09, P0.10) as GPIO?
I am...
Hello,
we are currently in the process of verifying the nRF LwM2M Client, specifically focusing on the Queue Mode functionality. During our testing, we encountered an issue...
Hello,
I am facing issue while initialising seed by calling "mbedtls_ctr_drbg_seed" function I am getting -0x34 error and when I analysis this I got to know that I have...
Hello,
It has been a while since I have done any controlled impedance and was wondering if someone could provide me a quick sanity check before I continue:
Here is the...
Hi,
Does nRF52840 support stable modulation Characteristics
It is found that Stable Modulation Characteristics fail during the test, and the capacitor of the debugger...
Hello everyone,
I'm using nRF52832 with SDK v17 (S132 Softdevice).
I don't know why, but I can't disable softdevice. I can enable it normally, but when i make use of...
Hi,
I’m looking to monitor LTE-M or NB-IoT packets sent by the Thingy:91 in real-time using an app or software. Currently, I’m using the Thingy:91 to send temperature logs...
Dear devzone,
I followed this instruction to use nRF54L15-PDK v0.8.1 to burn external boards. The wiring diagram is as follows:
Command line input: nrfutil device recover...
I have a Minew MSR01-B milimeter wave sensor and I would like to know if there is any nordic hardware that i could use to comunicate with MSR01-B sensor, get the data and...
Hello,
I am designing a battery monitoring circuit for a 3.0V CR2032 coin cell using the nRF52840, and had some questions. I am following the battery monitoring circuit...
Good afternoon,
I have successfully established a 2.4GHz Zigbee network using nrf52540 + Zephyr + ZBOSS. Now I need to switch to sub-1GHz band - suits better my application...
