Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Hello,
I am using the NRF52840 with the flash chip W25Q32. I tried using the sample program "Flash Sample" with my device set in qspi. I can get the flash device reading...
Hello and thank you for reading. We are using SDK 2.5.0 and the nrf5340, and would appreciate some help with the HID over Gatt functionality.
Our device implements multiple...
I have an application for a mouse with nRF52833, s140 and SDK17.1. The BLE advertising works in fast and slow advertising, and I'm following the indications by Microsoft on...
I'm trying to port a PPI application to an nrf5340. I'm quite puzzled, as it would appear there is no obvious way to achieve what I'm trying to do.
In short, I have a setup...
Hi,
I notice that every time I can only send 244 bytes per time in nus service, if I set higher I will not receive the data in RX.
But I also see that the thoughput...
Hello,
We're using version 7.0.1 of the S140 soft device. We are making a bluetooth application where the device behaves both as a central and peripheral. In peripheral...
we now have nRF52840 DK PCA 10056 , V3.0.0 . the documentation of product specification user guide available online is for v1.0 (old dk) , but not for v3.0 . please can you...
Hi folks,
I am just in the process of getting my feet wet with the nrf connect sdk and zigbee development is my ultimate goal.
I am using an ItsyBitsy nrf52840 https:...
Wireshark Windows version 4.4.5
nrfutil 7.12.0
ble-sniffer version 0.14.1
Somehow during the course of installing the nRF Sniffer, Wireshark got two interface toolbars...
Hi,
I'm working on a very high density board with the nRF54L15-QFAA (we want to prevent using a CSP) and I'm running into some routing issues. While looking for optimizations...
Hello, We faced with issue in which we are not able to get the time from the network and because we don't have time, we can't use JWT. As I understood issue is because of...
Hello everyone, I am want to write custom radio protocol for the nrf5340. I have already tried the ESB protocol. But that is somehow limited on the latency (I will open a...
I'd like to use the nRF52832 for cost reasons & I know there are different Bluetooth audio standards, which the nRF52832 does nto support the latest. I don't need hi quality...
Hi, I have a question about the WDT documentation in nRF5340 Product Specification v1.6.
Question 1:
The chapter "Reload Criteria" (7.41.1) is maybe a bit ambiguous defining...
Hello,
I am using the LTE IoT 4 Click board based on the nRF9160, with SDK version 2.6.0 and modem firmware version 1.3.6. I read in the documentation that the nRF9160 provides...
