I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hello,
I want to modify the lte_ble_gateway app (nRF connect SDK 1.6.0) to connect with the nRF52DK advertising through the ble_app_uart (nRF 17.0.2) application. The lte_ble_gateway...
Hello,
I am trying to test 1 central 4 peripheral multilink(with saadc).
However, when the master-slave(central-peripheral) is connected,
the connection disconnected...
As the title states, my program (and a simple idle/hello world program for that matter) pull approximately 600-800 uA at idle. Same exact program, driver, and config on my...
Hi all, I am trying to write a driver for a TMP116 temp sensor based off the existing Zephyr TMP116 driver. I have added in functionality to enable the interrupt pin to enable...
1. I am tried to clear DTLS session during lwm2m session using coap_security_destroy() . I have added logging and I can see ntf_tls_free() is called from coap_security_destroy...
I'm using DWM1001-DEV, which has UWB and nrf BLE features, and my ultimate goal is replicating Apple's Airtag with DWM1001-DEV. For this, I have to ensure the power consumption...
Hello. Our company develops an electronic device, that includes using of Bluetooth Low Energy technology. We do not familiar yet with the benefits of being a Member of Bluetooth...
Hello DevZone.
For my project I am using up to 6 connected peripherals to my central and I was watching the behavior of the link when one of the 6 devices disconnected...
Hello, I am brand new to antenna design and especially antenna tuning and want to know if my antenna tuning design/method would work.
First I will be tuning with a VMA ...
Hello,
I am using a nRF9160-DK(PCA10090, 1.0.0) and v1.6.1 SDK
I am trying to estimate battery consumption in some scenario.
For this test, UDP sample is used.
When...
Hi,
I am using a specific LED that has the PWM specification to drive as below.
Would it possible to drive the LED with nrf52840. I see the PWM clock upto 256KHz...
Hi Sir/ Madam,
I want to create a modul to scan and advertise data using Nordic Dongle , (PCA10059). The example code in sdk , ble_app_multirole_lesc has been tested with...
Hi Forum,
I'm using a NRF24L01 (without "+") in a very power critical application. To tune the matching networks, i used a mini coaxial connector on the output to measure...
