Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Hi,
Toolchain manager is failing to download SDKs.
I am using:
Windows 10 PC
3.7.0v nRF Connect Desktop application
0.9.3v Toolchain manager.
Downloading sometimes...
Where is the provisioning configuration data getting stored ?
1. EEPROM
2. Any other non volatile memory
Is it getting stored in external chip to nrf52833 or inside...
Hello there!
I'm quite new to the topic and just tried to dig into it a bit, so I'm sorry if I didn't get all things yet about the nRF5280 Dongle :) .
Right now, I'm following...
Hi all,
Using the thread CLI example (on a PCA10056 board) as a starting point I would like nodes to connect automatically to a thread mesh when booting. I then want to...
I use the following example source code to test NFC pairing.
Example source code for NFC: nRF5_SDK_17.0.2_d674dde\nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\experimental...
Hi
thank you very much for your paying attention.
Yes the peripherial_uart sample seems to be a good choice for my project. But Uart 0 pins didn't come out on GPIO connector...
Hi,
We are trying to create a network using 20 movesense sensors and BWG840 Fanstel gateway acting as the central. The gateway is running a modified ble app uart multilink...
I'm a beginner in BLE applications, and I'm having trouble with connecting nRF toolbox application
I wanted to use UART function provided in nRF toolbox.
But, an e rror...
Hi,
I wish to run an existing project in Segger embedded studio for its debug capabilities (Currently the project runs in VS code).
I'm using the nrf52832, running a bare...
I'm trying to add the unity test integration to our project, but failing to build, since the project has a dependency on nrf_oberon
For the sake of completeness, the project...
I'm having trouble connecting Thingy:91 to cloud.
I've installed both the modem and HEX image in the board successfully.
I've added the SIM card successfully to the...
I've had intermittent issues with the nrf9160 modem using mfw 1.3.0 with an iBASIS SIM getting stuck in "searching" state when first powering on. The symptoms are similar...
I am using a nrf_drv_twi_tx() and nrf_drv_twi_rx() for a simple I2C transaction but I'm noticing a strange behavior.
If I don't use APP_ERROR_CHECK(err_code); right after...
Hi,
We are developing a flutter mobile app, for Actility/Abeeway (chips from Avnet Silica) using flutter pluggin that relies on the Android SDK. In some situations (after...
