Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
software:ncs 2.5.0
hardware:nrf5340 dk
hi professor,
According to the article at https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/optimizing-power-on-nrf53...
I have found that in Linux, "nrfutil toolchain-manager launch --shell" is starting a process that uses almost 20% of the CPU according to the top utility. I have found this...
I'm trying to make a BLE beacon with Li-Ion battery and Qi wireless charging circuit. NRF52833 works in high-voltage mode (VDDH connected directly to the battery, internal...
nRF connect SDK 2.7.0 CONFIG_CHIP_LAST_FABRIC_REMOVED_ERASE_AND_REBOOT KConfig option is not working, it is not erasing nvs and not rebooting device. Although I have enabled...
Hallo,
I'm using Segger Embedded Studio to program nRF52840. In the Nordic nRF5_SDK there is the ble_app_uart example using S140 softdevice, which is running well. Now I...
I am trying to measure the current consumption on nRF52832 PCA 10040 2.0.0 with PPK 2 (PCA 63100 1.0.1).
I have cut the SB9 and connect the PPK as the picture:
as shown...
Im a bit stuck here.
I have the following code, trying to communicate with a flash memory:
Overlay:
code:
I get the following error message:
error: ...
Dear Nordic, I have developed an application for nRF52811 on nRF52840-DK.
For this i have referred examples -> peripheral -> template_project.
I have followed https...
I just fired up our most recent custom boards with nRF9161-LACA's, and tried to compile modem shell application for RTT.
I noticed the RTT is disabled because HAS_SEGGER_RTT...
I am working nrf52840 with bg96 modem, i have configured quectel_bg9x.c driver to communicate with bg96 modem from nrf52840.
can you provide a sample application on MQTT...
Hello,
I'm experiencing an issue integrating a freestanding Zephyr module with the sysbuild system. The module defines custom boards and projects. When I use the...
Hi
We are the Manufacturer of Smart lighting
We have start new project" Cellular gateway".
We are evaluating the nRF9160 Dk board .
During this we found issue . it...
Hello,
I have 4 nrf52840, 3 act as peripheral and the last is the central.
The peripherals are identical hardware with various sensors using the same FW. I order to...
SUMMARY
Attempting to OTA the nrf52840dk over BLE.
I was able to perform most of the steps in this sample: https://docs.nordicsemi.com/bundle/ncs-2.1.4/page/zephyr/samples...
I have a photodiode, and under indoor lighting conditions, the reading on the oscilloscope is about 150mV. When I connect it to an Arduino Uno or Adafruit nRF52840 Sense,...
