Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hi,
I need to save a 16 bit counter into a retained register.
I cannot use the 2 GPRETREG since they are already used and I cannot write internal flash.
I cannot use...
Hi everyone,
I’m facing a linker issue in NCS v3.0.2 while using the Zephyr HTTP client sample with TLS enabled , and I’m looking for guidance on the correct configuration...
Hi all,
On a BLE project I was working using version 2.5.0 of the VS Code dev environment I was able to set up a partition where I could store non volatile data, such as...
Hi guys,
I've been using the ADC with the internal reference of 0.9V.
However, to increase the scale of the ADC without using the gain 1/4 I've made a revision to the...
Hello,
we are testing the BLE ADV capabilities and also MESH performances on NRF54L15.
We verified that, in conditions of continuous scanning (interval = 30ms), the packet...
Description: I am implementing USB Mass Storage with a FAT filesystem on external MX25UW63 flash (via EXMIF) using the nRF54H20 DK (NCS v3.2.0).
Setup:
Board: nRF54H20...
Hi Nordic Community, I am working with the nRF52833 and I have a question regarding the electrical characteristics of the dedicated USB signal pins (D+ and D-) when the USB...
I thought that the nRF21L01 had been obsoleted and replaced with the nRF21L01+, but digikey doesn't list the + version but still shows the old one for sale. Has the part been...
I'm sending HCI command LE Set Transmit Power Reporting Enable with both local and remote reporting requested.
The Bluetooth Core Specification says "If the Remote_Enable...
On nRF54L15 DK (CPUAPP) the app boots and advertises fine, I bound my phone using nrfconnect but when I reboot the DK and try to reconnet using nrfconnect, the device hangs...
I have a new nrf9160dk board that I will be using for a BLE customer application. I am using zephyr/samples/bluetooth/hci_uart SDK V3.2.0 to be loaded into the nRF52840 in...
Hi Nordic
We would like to be able to read out the serial number off our devices, without connecting to them,
We have not enabled RFID on the product, but would like to...
Hello!
Our client encountered a problem in the development of Matter: the client wants to add or reduce endpoints dynamically during user usage after adding a cluster. Is...
how to create the nrf52840 mesh of more than 50 devices ?
I am using the chat sample for this mesh network but i am tested with the 12 boards but i am getting reply from...
