here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
I run the ./nrf/samples/bluetooth/peripheral_uart example on 52840DK and connect to it using the nRF Toolbox UART section.
The connection works and I can send messages to...
Hello,
I want to modify the lte_ble_gateway app (nRF connect SDK 1.6.0) to connect with the nRF52DK advertising through the ble_app_uart (nRF 17.0.2) application. The lte_ble_gateway...
Hello,
I am trying to test 1 central 4 peripheral multilink(with saadc).
However, when the master-slave(central-peripheral) is connected,
the connection disconnected...
As the title states, my program (and a simple idle/hello world program for that matter) pull approximately 600-800 uA at idle. Same exact program, driver, and config on my...
Hi all, I am trying to write a driver for a TMP116 temp sensor based off the existing Zephyr TMP116 driver. I have added in functionality to enable the interrupt pin to enable...
1. I am tried to clear DTLS session during lwm2m session using coap_security_destroy() . I have added logging and I can see ntf_tls_free() is called from coap_security_destroy...
I'm using DWM1001-DEV, which has UWB and nrf BLE features, and my ultimate goal is replicating Apple's Airtag with DWM1001-DEV. For this, I have to ensure the power consumption...
Hello. Our company develops an electronic device, that includes using of Bluetooth Low Energy technology. We do not familiar yet with the benefits of being a Member of Bluetooth...
Hello DevZone.
For my project I am using up to 6 connected peripherals to my central and I was watching the behavior of the link when one of the 6 devices disconnected...
Hello, I am brand new to antenna design and especially antenna tuning and want to know if my antenna tuning design/method would work.
First I will be tuning with a VMA ...
Hello,
I am using a nRF9160-DK(PCA10090, 1.0.0) and v1.6.1 SDK
I am trying to estimate battery consumption in some scenario.
For this test, UDP sample is used.
When...
Hi,
I am using a specific LED that has the PWM specification to drive as below.
Would it possible to drive the LED with nrf52840. I see the PWM clock upto 256KHz...
Hi Sir/ Madam,
I want to create a modul to scan and advertise data using Nordic Dongle , (PCA10059). The example code in sdk , ble_app_multirole_lesc has been tested with...
