Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I use Eclipse, gcc and OS X to compile.
I had FW working just fine with SD 6 and SDK 5.2. I recently tried to upgrade and ran into many problems, but the latest is the...
Hi
I've written an application that uses the gazell proprietary stack for nrf51822 and I want to use OTA-DFU using BLE.
Is it possible to upload the new firmware using...
I’m running into a problem with the SoftDevice safe twi that’s been posted in the forums a few times. I got the file here:
devzone.nordicsemi.com/.../
One of my peripherals...
Hello,
I have been messing around with a PCA10001 Dev board trying to do some power consumption tests (Beacon demo code). When I enable RTC1 only and use __WFE in the main...
Hello everyone,
I haven't read anything in the official documentation about it, but I was wondering if the S110 has an embedded checksum that I can use to verify its integrity...
Hi,
I'm currently working on nrf51822 beacon connected with stm32f4 board. able to communicate fine on UART as well as with bluetooth device. is there any way to find out...
We have been using the nRFgo nRF51822 development kit for prototyping. We now want to design our production board. However, your site says that this dev. kit is not recommended...
It seems these functions are identical in what they do, except that one is in S120 and the other is in S110.
Why not standardise the booting mechanism to facilitate code...
Hi !
I'm developing a bluetooth low energy service using the nordic evaluation kit and following the ble_lbs example. It works, but when I load the code on an other electronic...
Hello,
does the iOS Loader app not work with the nRF51422 chipset? I thought that this chip was more capable than the nRF51822. I do not seem to get access to the download...
I'm concerned about stack overflow as I consider using a linear fit function which declares 5 local variables as floats and accepts 5 pointers.
5floats * 4B/float + 5pointers...
Hello! Can anyone tell me information about bluetooth protocol and SDK functions?
What functions need to start BLE device like a peripheral/central, and what each...
My JLink Lite seems to have died (nRFgo Studio can see it, but can't connect to a target).
What is the latest replacement for a JLink Lite?
Preferably something that can...
I'm trying to get the ble_central_s120_pca10028 app working on my device. However it doesn't behave as mentioned in the user guide (no BSP_INDICATE_CONNECTED on peripheral...
