Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hi! I am trying to get the samples "Bluetooth: Direction finding connectionless locator" and "Bluetooth: Direction finding connectionless beacon" to work on nRF54L15dk. I...
Cannot program our nRF9151-SMA-DK, we have other boards and work normaly. This is the programmer log:
08:30:21.996
Initialising the bundled nrfutil device
08...
nRF54L15 - ncs 3.02 - toolchain 3.02
I changed my build settings from no sysbuild to sysbuild in order to use serial recovery and/or FOTA. I thought everything was OK until...
Hi,
For my university MEng group project, I am working with the nRF5340 Audio DK and Bluetooth LE Audio (LC3 over ISO).
My end goal is to stream audio from an nRF5340...
hi,
i'm a beginner for nrf9160DK so can you guys help me to how can i nrf9160 up and running for the first time. i'm not able to up and running with this video https://www...
I have a problem where the GPIO pin is not working as intended (it is constantly high but it should be alternating high and low). Via debugging I've ascertained that the problem...
Hello, I am encountering a crash in MCUBoot when using the following configuration:
MCUBoot as bootloader (SB_CONFIG_BOOTLOADER_MCUBOOT)
TFM configuration (build /ns...
I am encountering a build error while setting up a build environment. Can you provide assistance as to what the issue I am encountering may be? I am using VSCode on MacOS...
hi,
i'm stuck at lesson 3 exercise 1 in step 1 so i create an application with choosing option 1 create a blank application for this first task to print hello world and...
Exhausted everything. Here's the guts of the code. A task is called at 2Hz to push the value, which at 1024/s makes an event time of +512. I set the cumulative RPM to +1 for...
Hello,
We have a nRF9160 product in production that is programmed with an image created by SDK 1.9.0 and with the default memory partition. We migrated to SDK 2.3.0 last...
Hi there, I'm working on a low-power LoRaWAN project using a custom board featuring the ISP4520 module which contains the nRF52832 chip and has a LoRa section based on Semtech...
Hi,
I have detected a possible issue either in the SDK or the silicon related to the NFC tag. In my project we shut down the label and enable it based on certain conditions...
hi,
can anyone help me with this issue that i'm getting while i try to connect VCOM port and run the program. i got the one message from it is access is denied and i try...
Hello. I am using an nRF52832 in an HCI UART connection with my application processor. I'm running Zephyr 4.2 on both MCUs. I'm using MCUMGR and MCUBOOT to get OTA FW updates...
