Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hi,
I am going through the DevAcademy Bluetooth LE lessons, using nRF5 DK. But I run into problems directly in the exercise of the first lesson. Everything goes fine to...
Hello Nordic community,
I am currently working on developing applications for Matter over Thread and have set up my ZAP file accordingly. I've successfully flashed two types...
I want to use a switch in the overlay file, like:
To do so, I try to add a config statement in a custom KConfig file. (mp_Kconfig.conf):
Adding the file to the build configuration...
Hi,
We have come to expect that with the nRF Connect SDK installed properly and using recommended options we can build a sample, for example
$cd \ncs\v2.8.0\nrf\samples...
I am trying to complete the exercise, however, it seems that the only terminal output I receive is from whichever thread is run first, irregardless of whether I use k_yield...
I'm trying to setup an nRF52832 to drive 127 ws2812 by using PWM. It seems the bit-by-bit method is too slow for the 1.25uS period. pwm_set() is using somehow ~5ms, so that...
SDK : 2.6.1
uC: nrf5340
Hi,
how to avoid erasing of the application settings when updating the firmware via bluetooth.
When using the android version of "nrf connect...
I can program the spi and i2c find on my nrf54l15pdk board version 0.2.1, as soon as i turn on CONFIG_BT =y the device fails to do anything past being flashed successfully...
Hello,
I am looking to use the nRF9151 module.
I spoke with my wireless provider and asked what certifications they require to use their service. They said that they...
I am working on zigbee network
"In a Zigbee network, how can the coordinator retrieve the list of all devices connected to the network?"
What is the recommended way to...
Hello,
My team and I are working on a project where we need our nRF5340 to send data via UART from the board to a RaspberryPI. We designed a custom PCB with the chip and...
Hello,
We have devices in the field using NRF9160 V2 with NRF SDK 2.3.0 and MFW 1.3.4 on a Actinius Icarus V2 board. They are mostly working great, but sometimes some devices...
Hi, I am using nRF52840DK SDK 2.5.0 for testing Zigbee. I have three boards of this type, for the coordinator, router and end device.
For testing I use the end device I...
I am encountering the error <err> flash_nrf: invalid address: 0x00100ff8:8 when using NVS in my custom Zigbee project. However, the NVS functionality works properly in the...
I have a question regarding DFU while transitioning from development using the nRF52832 with the nRF5 SDK to the nRF5340 with NCS. Currently, I have a DFU app developed for...
