Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
Hi all
We observed a strange behaviour with mcuboot / bootutil in our nrf9160 based project.
The bootloader log messages showed that something with the primary image is...
I run the ./nrf/samples/bluetooth/peripheral_uart example on 52840DK and connect to it using the nRF Toolbox UART section.
The connection works and I can send messages to...
Hello,
I want to modify the lte_ble_gateway app (nRF connect SDK 1.6.0) to connect with the nRF52DK advertising through the ble_app_uart (nRF 17.0.2) application. The lte_ble_gateway...
Hello,
I am trying to test 1 central 4 peripheral multilink(with saadc).
However, when the master-slave(central-peripheral) is connected,
the connection disconnected...
As the title states, my program (and a simple idle/hello world program for that matter) pull approximately 600-800 uA at idle. Same exact program, driver, and config on my...
Hi all, I am trying to write a driver for a TMP116 temp sensor based off the existing Zephyr TMP116 driver. I have added in functionality to enable the interrupt pin to enable...
1. I am tried to clear DTLS session during lwm2m session using coap_security_destroy() . I have added logging and I can see ntf_tls_free() is called from coap_security_destroy...
I'm using DWM1001-DEV, which has UWB and nrf BLE features, and my ultimate goal is replicating Apple's Airtag with DWM1001-DEV. For this, I have to ensure the power consumption...
Hello. Our company develops an electronic device, that includes using of Bluetooth Low Energy technology. We do not familiar yet with the benefits of being a Member of Bluetooth...
Hello DevZone.
For my project I am using up to 6 connected peripherals to my central and I was watching the behavior of the link when one of the 6 devices disconnected...
Hello, I am brand new to antenna design and especially antenna tuning and want to know if my antenna tuning design/method would work.
First I will be tuning with a VMA ...
Hello,
I am using a nRF9160-DK(PCA10090, 1.0.0) and v1.6.1 SDK
I am trying to estimate battery consumption in some scenario.
For this test, UDP sample is used.
When...
Hi,
I am using a specific LED that has the PWM specification to drive as below.
Would it possible to drive the LED with nrf52840. I see the PWM clock upto 256KHz...
Hi Sir/ Madam,
I want to create a modul to scan and advertise data using Nordic Dongle , (PCA10059). The example code in sdk , ble_app_multirole_lesc has been tested with...
