Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
I noticed that the nRF9160s I2C low level logic voltage is quite high. With a 2kR resistor at 3.3V it's already more than 200mV. Because this is quite high and will...
Hello all,
I am using the BLE app UART code. I m trying to connect one plus through BLE connection. but nordic devkit BLE is not visible.
I am using the default configuration...
Sorry but I find the documentation useless. I don't even know where to start. It could be I have not found the correct documentation which is not surprising.
The best I...
Hi
I've built a USB HCI fimrware based on the sample from the nRF Connect SDK for the nRF52840DK.
See also: (+) HCI USB based on nRF Connect SDK 1.7.0 failed to update...
The SDK version of the program I developed with SES is v1.5.0. Now change the development environment to vscode and import the program into vscode through "add an existing...
Hi,
Is it possible to generate a passkey before initiating the pairing process?
The peripheral in my system does not have a display or input, so I'm looking for a way...
Hello Developers, I am currently developing an application on top of mqtt-sn publisher example. Now i want to add OTA DFU in my mqtt-sn based application. I have started up...
Hi, dk:PCA10095 sdk:ncs v1.7.0 example:path:D:\ncs\v1.7.0\peter\11_hello_world_pdm_i2s
Download changes when I build the project using SES: Previously: Download code available...
We used the nRF52840 in some projects, but there are still some problems with the short bridge at the IC during production.
So we want to leave the blank layout of the unused...
HI
We have to try to develop a product with nrf5340. The product needs to be waterproof and also it made up of metal and a small amount of plastic enclosure. In that how...
Dear Members,
I want to run ANT+ code in my custom board,
It works well on PCA10056, I can upload softdevice and the code to custom board board,
but I didn't get any...
I've recently upgraded my SDK to 1.6.0 and I am now unable to read the state of P1.00 but I am able to read the state of P0.28.
I've stripped the project down to just a...
I recently installed nRF Connect SDK using the Toolchain manager. Install went through without any issue but when I am trying to open an example project in SEGGER Embedded...
Hello,
I have a nRF52840 and am unable to flash an application to it. I am trying to flash the "examples/ble_peripheral/ble_app_blinky/hex/ble_app_blinky_pca10059_s140.hex...
