I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I having issues when merging softdevice and application hex files together. If I use nrfConnect and I add the two hex files not merged ( ble_app.hex and s132_nrf52_7.2.0_softdevice...
Hi. I was wandering if there is a difference if I put the TASKS_CALIBRATEOFFSET before TASKS_START , and vise versa. However, I saw in this link: infocenter.nordicsemi.com...
Hi,
According to the documentation the maximum admissible current for the DUT in ampere mode is 1A. What happens if the current goes higher than this ? I suppose that it...
Hi,
I would like to store 180 000 bytes on the flash with fstorage. By using the example after some trouble it works. When I try to apply this example on my own program...
I've seen several questions on this forum on issues with setting up the NRF LOG, however, I am still having many issues and I can't seem to get UART logging working.
I am...
Trying to test the 1ms sample on the NRF5340DK. Loaded and ran the app without problem.. it starts with 9XXXXus. Runs with couple of drops. But when 1ms interval is started...
Hi there,
I have the following settings:
- nrf52810 on a custom board
- only the mandatory GAP service and one custom service with three characteristics, everything...
Hi all,
I have the following issue: For an electrochemical measurement I need to use 4 GPIO pins bundled in pairs, each pair with an output (GPIO HI) and ground (GPIO LO...
I'm evaluating nRF9160 + Serial LTE Modem application for a battery powered device that uploads data via HTTP POST 8-12 times per day. Since all interactions are initiated...
Normally when we send data via UDP we get a +CEREG: 5 response.
We use this to generate a signal <e_ready which in turn allows the next message to be sent.
(As per the...
Hi
I wants to do POC on LE audio, I know nrf5340 support all Bluetooth5.2 spec. Where can I found LC3 codec that can help me for POC? is Zephyr LC3 codec can help?
https...
I'm doing a bit of research on Nordic Semiconductor devices and am currently looking into devices that use a nRF52x chipset.
I have been looking around the internet for...
Hello , I am working on a project which contains I2C communication, When I test the twi scanner example on my sensor and it works fine But when I do the combination with the...
I'm trying to update our LTE connection library to use the LwM2M Carrier library to be prepared for carrier certification and I am not seeing any way to request that the modem...
1.Project only has one main.c file. Other files are in zephery public folders,like conn.c etc.
My problem is ,if I modified conn.c for one project, how about the other project...
