I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Hi everyone,
Looking the nRF52840 Product Specification v1.1, I see that there are several System Off modes.
1. Using the function sd_power_system_off() what is the by...
Hi,
i'm new on using nRF5 modules and i have some question about how to program the nRF52840 on a custom board, so with a completely new chip.
Reading the schematic of...
I am using nrf52840 DK (pca10056) board and nrf5SDK 16. There is one low power sensor connected to the board via SPI interface. My program consume less than 30uA before I...
HI:
I transfer the init packet and firmware to bootloader successfully by UART DFU, and then the app can not start. It report error as below:
<00> info> app: Inside main...
Hi All,
My update of nRF Connect v3.3.0 failed after a while:
Update of nRF Connect failed with the following Error-MSG:
On the same day I got an install from Oracle...
Hello everyone,
I would like to use the PPK with a NRF52 Dk, but I have external sensors connected to the VDD and 5V, so when I will plug the ppk I will have to disconnect...
Hi,
I am reading a 24-bit data from SPI by getting a data-ready interrupt from GPIOTE pin in a NRF52832 chip. I have to buffer data for the BLE interval duration then send...
Hi,
I am using BLE-UART example in my project and to start advertising I am using below piece of code.
By default in the sdk (ble_advertising.c) the advertising type...
Hi,
I don't want the spm and application firmware built together so I tried using the "spm" sample in version 1.3 of the sdk. However when configuring the project i t...
I have a requirement that my peripheral device should only rely on the central to start any security operation. Right now I see a problem when the central side removes the...
I am new to BLE with my nRF51. I've got this example and I try to stop a RSSI scan when the device get all advertising data from the local device.
But when I try to add...
I burned this program in nrf9160 ncs v1.3, and how do I fix the following error?
An example can be found in the figure below
Example prj configuration see figure ...
Hi,
I would like to evaluate the NRF52811 chipset module (BMD-360 from UBlox) using the NRF52840 DK.
If I am to read the Constant Tone Extension that will be transmitted...
I followed an instructions developer.nordicsemi.com/.../gs_assistant.html in the case of Kubuntu 20.04 and developer.nordicsemi.com/.../gs_assistant.html in the case of Windows...
Note: This is related to the following issues:
- https://devzone.nordicsemi.com/f/nordic-q-a/63255/nrf9160-getting-stuck-after-cell-change
- https://devzone.nordicsemi...
