I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi All,
I am trying to understand the possibility of using Bluetooth Mesh technology for voice communication for longer distances.
My main problem is to communicate longer...
Hi,
I was wondering if it was possible to notify the application layer if the central device is scanning and it (the central device) sends a scan request to an advertising...
Hi,
I have two questions regarding the UART and SPI communication at high speed.
I am using the UART and SPI to transfer data on nRF52832 and sdk 17.0. I connected an...
Hi Team,
I try to design a PCB based on nrf52840 chips, can you help me check if it is right?
Something like Power supplement, SPI interfaces, and debug and programming...
Hello,
I am currently using nRF Connect SDK v1.7.1 with a nrf9160DK. I keep getting "create_nordic_project.py filed (1)" when I try to open a new project with a overlay...
Hi, I am trying to measure power consumption (the device is an nRF52840 dongle) and I get different results when the board is connected or not to a JLink external debugger...
HI
I need to port my application from NCS v1.5.0 to NCS v1.7.1 Here, I have already tried to transfer my ble application to a higher version. I can't able to do pristine...
@Nordic Semiconductor General Chip nRF9160 rev2 Voltage 3.7 PSM Periodic TAU 5.0 hours Periodic TAU timer element "00011110" Active time timer element "00000000" RRC connected...
Hello,
I have implemented a somewhat working RX algorithm for receiving data over UART but I'm looking for a good way to make it more robust. I haven't found any good answers...
Hello,
I'm try to follow the instructions for multi image example.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_nrf5340.html#ug-nrf5340-ses-multi...
Hello
I have 2 custom boards both with nRF82532. One is central and the other a peripheral. I use LESC. When no bonding information is stored in either of the devices, pairing...
Hello,
I am using mfw1.3.0 and NCS 1.7.0 developing an application on a custom board implementing the NRF9160 and NRF52820 (The 52820 is put into very low power using nrf_pwr_mgmt_shutdown...
Dear Nordic,
we need to save few bites (product serial number, few settings). we use BLE with bonding on a FreeRTOS based FW. PM is already using FDS, at it is not clear...
