I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
I'm trying to flash to a nRF9160 with nrfjprog. The hex file works fine, and can be flashed from other (windows) computers. But any change i'm trying to make with nrfjprog...
When I use this example:ble_central\ble_app_uart_c (SDK_17.0.2 S132 nrf52832)
It disconnects every few seconds and reason 0x8.
LOG :
<info> app: conn_Param Update...
Hello! I'm reading the functions that exist in SPU HAL.
The function nrf_spu_flashnsc_set is used to configuring non-secure callable flash region. Which is great to use...
Hi,
I am using the nRF52833DK with NCS v1.6.1 in SES for a multiperipheral application. The application has the LIS2DH accelerometer which is communicating with nRF52833...
I'm using nrf_sniffer_for_bluetooth_le_4.0.0 on Ubuntu 20.04.3 and running `./nrf_sniffer_ble.py --extcap-interfaces` fails on my system. Which also means the nRF52840 dongle...
Hello,
I would like to implement an I²C communication between a nrf52840 and a MCP3221 (which is an ADC).
The first 7-bit of the MCP3121 are 0b1001101. I guess the slave...
Hi!
I have a custom board based mostly of the nrf9160DK, where I need communication between nrf52849 and nrf9160 processor.
I have used the code from this ticket that...
Hi,
I'm using the PCA10056 dev kit and nRF5_SDK_17.0.2. I am aiming to connect multiple initiators to acceptor using Initiator and Acceptor examples. So far I've been able...
Hi There,
When I am trying to write code, I am not clear about the meaning of the code " bearer_adtype_add( BLE_GAP_AD_TYPE_COMPLETE_LOCAL_NAME ); "
I try to check the...
I'm using the Zephyr provided WS2812 LED driver (SPI). I am noticing some strange behavior when my chain-length property is greater than 10.
I connected a digital logic...
Hi Nordic
We are developing our IOT product and we are starting our development of firmware on nRF9160 DK so that we can port that code to our custom PCB that will contain...
Hello
When I output some data using a 'LOG_xxx' macro, I do get debug information over the RTT console like this:
But as you can see there are some extra bytes in front...
Hello,
I wish to send SPI message by 2 Bytes per once, total 102 bytes.
Basically SPI works fine.
I wonder if there is way to reduce inter SPI time. It measured 18u...
Hi,
We are looking at porting the Tuya BLE SDK to the Nordic platform and on reviewing the documentation we have identified that the SDK uses two 16bit service UUIDs:
...
