Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hi
I wanna use second pin of nRF52832 as a gpio output pin.
I'm using software as a follows.
・nRF5_SDK_17.1.0_ddde560
I don't know which function programs I must use...
Dear, 1. what maximum voltage may be applied through the two pin connectoe marke External Supply on nRF5340Dk kit? 2. Does the Debugger works with external supply also or...
Hi,
Simply asking, what is the difference between nRF Connect SDK and nRF Connect Desktop? I would like to program nRF5340 DK with a feature of ble coded PHY (ble with...
Hello,
52840 MAXIMUM_TX_POWER is 8dB,
it support long range transmission,see Test reports & deployment recommendations — Fanstel
5340 MAXIMUM_TX_POWER is only 3dB...
we are using "nRF5_SDK_17.0.2_d674dde" and nRF52832 chipset to develop software, after build via SES, we try to merge the app hex file and softdevice file, but it fails. ...
Hi,
We want to know more about DMA in I2C,
we are using TWI Master and Slave drivers as mentioned here in this blog https://devzone.nordicsemi.com/guides/nrf-connect...
I've been trying to build blinky using the nRF SDK from the toolchain manager with no success on windows 10. I've previously been able to build projects so I'm not entirely...
I would like to make my own project of an analog sensor with BLE feature. Is it a good idea to go with third party module (because of the easy availability of Antenna)? can...
Hi! I measure the micro frequency by Hantek Osiloskop in two-mode.
First, I use a simple Blink without softdevice , reaching 570kHz in 10us. Second, I use a ble_app_blinky...
Hi, I am looking for some help in interfacing STM32F4 MCU and nRF52832 module via UART for establishing BLE communication. My application needs both the devices.
I downloaded...
Hello everyone,
how can I implement a blacklist for my central which is scanning for a UUID and should also check for example device name. If the device name is in the blacklist...
We have developed a sensor application using ESB protocol with the nRF SDK (nRF52832 on Tx side and nRF52840 on Rx side).
We would like to redevelop now the receiver under...
Hi
1、I made the following modifications to the hello_world example（ncs1.7.0\v1.7.0\zephyr\samples\hello_world.
2、I have disabled uart0,But the average power...
