hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hi,
I am Maria from SmarEdns. We need a hardware device that connect 15+ BLU at a time and update firmware. how many BLU connection avaliable in nRF52840 Dongle at a time...
Hi,
I am using fstorage functions in the ANT broadcast RX project.
I am doing the fstorage write function when the ANT device is connected (Inside RX EVENT of ANT event...
Hi
I need to change the default mtu size（peripheral device）, but it always 23，unless phone requeset mtu size.
ncs2.7.0
nrf54L15pdk any peripheral demo
I need this...
Hi
I know , there are several threads on this subject, but I would like to know if there is a sample that works out of the box on the thingy91.
If not, is there an alternative...
Some time i got this error msg
error] [ Client] - Encountered error -105: Command connect_to_emu_with_snr executed for 40 milliseconds with result -105 ERROR: Unable to...
Hello, I have a question regarding the watchdog with secureboot.
I just added watchdog to my app, but I'm worried that when I DFU the HW watchdog will trigger during the...
Hi,
I have tried to look through the forums but I cannot find exactly how the nRF Connect -> Power Profiler application is able to get/obtain the device SN?
In the log...
Hello, we have a project with nRF5340 and SDK v2.6.0, and we can not obtain the logs from the network core b0n bootloader , but we do receive properly all the other logs....
SDK:17.1.0 application: ble_app_uart(+ble_app_buttonless dfu service) bootloader:secure bootloader pca10040e_s112_ble Background: There is only one key(pin:31) on the PCBA...
Hi there, I am trying to use shell with the USB and logging with RTT. Additionally, UART0 async is used to communicate with sensors. Here a snapshot of the proj,config:
...
I'm developing a custom board with a uBlox NORA-B121 module, which contains an nRF5340. The board has a Microchip MCP2515 CAN controller, and for some reason, I can't receive...
I am porting an application from NCS v2.3.0 -> NCS v2.4.0. My application runs in nrf5340dk_nrf5340_cpuapp_ns with NSIB and mcuboot. The mcuboot uses external flash for the...
I have Thingy:91 dev board. I have flashed hci_lpuart sample to nrf52840 and successfully ran lte_ble_gateway sample. Now in my application I want to connect to the same hard...
Hello,
I'm trying to reduce the power conception of my custom board with a nrf52840 and a 4g modem on uart.
For this test, I reduce the code to a loop (modem is off...
NRF52840 running 17.1 SDK and using QSPI interface to erase a block of memory from AT25FF321A external flash IC.
When we call erase it takes 930 millisec to finish erasing...
