Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hi, I noticed that when using nrf5340 and it's kernel timer driver, that the k_cycle_get_64() API is not available, and that TIMER_HAS_64BIT_CYCLE_COUNTER is not being set...
Hi,
I’m planning to use a chip antenna that meets the attached specifications. I’m not very familiar with RF hardware, and I’ve only just started using CAD. I placed it...
I have a nrf52833 small board. nrf52833 QFN
and the several board have the same finding: at first time, the board can be flash and be debugged to main entrance.
but ,...
Hello this is my first time making rf circuit and i would like to get feedback on this circuit with nrf54l15.
I used Texas_SWRA117D 2.4GHz IFA antenna.
Calculated...
my nrf52833 board cannot work after power. but can start when I run nrfjprog --reset . but when I power down and power on the nrf52833 board, it do not work. the following...
When building the blinky sample with CONFIG_CLOCK_CONTROL_NRF=y set in prj.conf, the build doesn't enable the clock control and gives this warning:
Steps to reproduce...
I’d like to ask: I created a BLE keyboard based on nRF5 SDK + 52833 + S140, and it can pair and bond with Windows successfully. I have two questions:
If the keyboard...
Hi,
I am running(build and flashed successfully) the Channel Sounding example(connected_cs) from the Nordic sample and currently I want to see the distance estimation logs...
Device: nRF54L15 x 2, face to face
SDK: v3.2.2
Toolchain v 3.2.2 c717907b94
Sample code (with default setting):
channel_sounding_ras_reflector
channel_sounding_ras_initiator...
Hi, I am currently testing the channel sounding capabilities of nRF54L15 with zephyr on NCS 3.2.3. I used the sample code from nrf\samples\bluetooth\channel_sounding_ras_initiator...
Hi folks,
I'm using v3.2.2 of the nRF Connect SDK Toolchain, debugging an nRF54LM20-DK board in VS Code.
I've noticed that the "Thread Viewer" under the NRF Debug view...
Hi,
I'm trying to deal with a weird issue regarding writing files to an SD card. I am restructuring my project to be more maintainable, which means moving some things over...
I want to use nrf52840 dongle as sniffer to catch 802.15.4 packet.
But after I use "nRF Connect for Desktop v5.2.1" to program the nRF Sniffer firmware(nrf802154_sniffer_dongle...
Hello Team,
I tried building an example application available in SDK v3.0.0 for Thingy 91x_nrf9151. But its showing some build issues. Which I am not able to figure it out...
Hello Team,
Recently we had purchased Nordic Thingy:91x from you. But when we tried Out-Of-The-Box we were not able to sync device data to the cloud. We had connected Onomondo...
