Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
I am using nrf52832_xxaa and I'm porting my device from SDK11 to 14.
I have found that new sections have been added in the linker file of the examples like sdh_soc_observers...
Hi,
I use SDK v13.0.0 with SD S132 and to debug my application I use UART0 on Putty.
When I use SPIS (0) (no BLE and no softdevice) alone I perform all functionalities...
hello：
i use timer1 to get a pwm waveform，when i use RTT to test it，the waveform is ok，but when i take out the RTT，and Remove the battery and put on the battery again to...
I've made a custom board with nrf51422-QFAC, which I can program with nrf51-DK. I'm using SDK 12.3.0 and SD130, which is flashed to the custom board.
When I program the...
I'm trying to setup logging with printf() over UART and I got totaly blocked by following realy strange situation.
Let's have following very simple log_test.c:
Then...
Hi. I'm quite new to nRF programming. I successfuly solved how to compile/link/flash the software onto nRF52 DK using just a simple editor (Notepad++), the ARM toolchain and...
Wondering if there are any example/reference implementations of a bootloader for the nRF51822 that support Device Firmware Update over both UART and BLE? We've got the BLE...
Hi,
I have met problem when apply dfu of nrf52810.
I used dfu sample of 52810 from devzone link: https://devzone.nordicsemi.com/f/nordic-q-a/28471/about-ota-for-nrf52810...
I met a big issue when implement the voltage level switch. I used nRF52832's SPI to communicate with an ECG sensor which has 1.8V SPI. The issue is that, 3.3V signal from...
Having just got the DFU functionality working I got the task of trying to add NFC functionality to the application. The code side was not a problem since I got a c and h file...
According to the BLE 5.0 Specification :
"The Link Layer shall use the primary and secondary advertising channel
indices as specified by the Host, and the used primary...
Hi,
There is a bug in a Linux box (Mint x64) with the following configuration:
SEGGER Embedded Studio for ARM Release 3.34 Build 2017121400.34532 Linux x64.
Nordic...
Hi,
I am using ble_app_multilink_central and ble_app_uart central example for my application, i am combining these two example for ble_app_multilink_cenntral for BLE_NUS_C...
Hi,
I'm using the nrf_drv_twi driver (master) to communicate with a number of IO components, such as LEDs, buttons etc.
If my IO component does not respond (why is not...
I downloaded SDK 12.3.0 (seems to be it is the last supported SDK for PCA10028) and tried to use fats example, I changed pin configs to SPI's pins.
I also prepared my 16Gb...
