I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hi
I am developing some nodes that all using BLE in nordic chip, I want each node get some data at the same time and send to one central device, the central device can fuse...
Hi,
I am wondering whether I can have one "RELAY" device in BLE communication (not BLE mesh), I have look through this forum but only saw some example 5 years ago. As I...
Hi Support team
1) What is the actual minimum operating temperature of nRF51802?
2) Could you help clarify more details about the temperature sensor(TEMP) of nRF51802...
Hi,
Our team is trying to disable the Access Port Protection (APPROTECT) for the nRF5340. The main goal for this is to be able to start breakpoint debugging without needing...
Hello,
I recently bought a nrf52840 dev kit + dongle to test the functionalities of Matter.
To commission devices "On network" without the use of Bluetooth, i wanted...
I tried the WindowCover sample with the latest SDK 2.9.1, on NRF5340DK.
The sample reports the attribute when manually control the lift.
However, when controlling the...
Hello,
I get "data_len_update failed (err -5)" error message in lesson 3 exercise 2 of Bluetooth course. I have posted the output log below. Any idea why this is happening...
Hello!
I would like to report a bug with the nRF Connect for VS Code extension.
My setup
VS Code v1.98.0
nRF Connect for VS Code Extension Pack v2024.9.5
nRF Connect...
Hello Nordic Engineers and community members,
I received an nRF7002-DK 1.0.2. (S/N: 1050757935), from Digi-Key today.
I've been following the YouTube video, "Getting Started...
Hi, We're using the nrf9160 with ncs 2.7, modem FW 1.3.6 We're trying to send an HTTP request with TLS 1.2. We have provisioned our device and verified the key,cert with a...
We are using SDK 2.4.0 and have enabled MCUBoot to support OTA updates using the dual slot method. I have reviewed many posts and existing tickets and have not been able to...
hello everyone,
I am using the nRF52840-QFAA-R7 (48-pin package) along with the nRF52840-DK development board. I have a question regarding I²C communication. Currently,...
Hello everyone, I am planning to make a wireless keyboard, and one of the requirements is that it has a long battery life, so I am very concerned about the power consumption...
So I've been playing around with some code example to make UART work (which I did eventually) using NRF SDK 5 (v17). However the last version of SES (8.22a) requires some...
I am having issues using a keypad to wakeup an nrf52840 and am unclear on if the GPIO sample is relevant if using a kbd_matrix device definition. I would like to use "sys_poweroff...
