Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Hi all,
In the PDF version of nRF54L PRELIMINARY DATASHEET v0.8, in chapter
9.1 Debug access port: in table 65: Access port overview
is listed AUX access port of AHB...
nRF5340Dk with NCS 2.6.1 and toolchain 2.6.1.
I want to measure 6 frequencies for my application, these frequencies would be attached to GPIO pins and needs to be measured...
Hi, I'm learning the nrf51-powerdown-example <system_off_wakeup_on_gpiote> from github.
My understanding of the code is:
1) When button 0 (Power down) button is pressed...
Hello, trying this and that with a qwiic relay , first a test on i2ccl then VS using a 9160DK. (i2ccl -> pip install i2cdriver ) returns a status of 0x00 that relay is not...
NCS 2.7 with sysbuild + mcuboot
NRF52840 (custom boards)
In my previous projects with NRF5 SDK I found it was very helpful to define a section in the linker so the rtt...
Hi,
I have a two part question aimed at optimizing the battery life during BLE transmissions. I am using an nRF52805 with the S112 soft device and a DCDC regulator connected...
Hi,
We have a custom board with a nRF9151. We're still sorting out LTE connectivity issues but I wanted to try out the location services with GNSS only for now. I modified...
I am building a Bluetooth controller with channel sounding feature enabled. The project uses an external Bluetooth host along with the hci_uart example. The prj.conf file...
Hello, I am using nRF Connect SDK version 2.9.0, and I want to know how to perform the software interrupt.
Where can I find the driver of the software interrupt to know...
startup_config.h is included in the file 'arm_startup_nrf51.s' but it does not exist in the nrf5 SDK. Where is it located?
I note there is a comment about the nrf5...
I have the same application that runs on both nrf51 and nrf52 MCUs. The Bluetooth in the application uses SoftDevice and not the SDK primarily because I started with the pc...
While evaluating low power mode on SBC I notice something strange:
- PPK II measuring 76mA
- LAB power supply measuring 67mA of supply current
- Digital multi meter...
I have nRF Connect SDK v2.9.0 and an nRF54L15 DK.
Is it possible to build the Zigbee NCP Sample for this board?
The source files under the Zigbee NCP Sample directory...
Hello everyone,
I have zepyhr running on the Cyclone V according to the following instructions: https://docs.nordicsemi.com/bundle/ncs-2.5.2/page/zephyr/boards/arm/cyclonev_socdk...
Hi,
I am using the SAADC (AIN2) to get temperature values from a Pt1000, and I am experiencing sometimes strange behaviour after the offset calibration is done.I have quite...
