I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
Hi,
I am using nRF52840 as a peripheral + want to add UART to communicate with like Arduino and GSM. Is there any project that I can use/follow. Thanks.
I see LESC_DEBUG_MODE defined in some of the examples in the SDK (17.0.2) but I can't see where this definition is referred to in any of the libraries, so I don't think it...
I am facing strange issue when I execute firmware with NRF_LOG_ENABLED set to 0.
During BLE communication, Firmware is crashing.
If I enable NRF_LOG_ENABLED, all is working...
My requirement program flow is clearly written down .Please help me out.
void USART_EVENT_Handler()
{
// disable timer 1
//disable timer 2
// clear timer 1 count...
HI,
I have already got output from each of the SHT20 and MLX90614 sensors. Now I want to combine both the code. Regards, I need an help to Setup prj.conf file
Thanks &...
I'm referring to the HID keyboard example (BLE peripherals)
The example itself is more or less working and since my goal is to send a whole character string via BLE and...
Hello, Nordic!
When a scan is started with certain scan parameters, a timeout event (NRF_BLE_SCAN_EVT_SCAN_TIMEOUT) will occur in a time less than the specified timeout...
How can I do a point multiplication in NRF52840 using the ECC hardware accelerator for the secp256k1 curve? Also are there examples or any documentation on how to implement...
Hi,
I'm openning a new case (following the proposal of Einar Thorsrud ).
I want to do a BLE NUS project with custom service 128bits and with custom characteristics also...
Greetings!
Using the NRF52840 PDK, I succesfully erase, write and read without any modifications!
I have custom boards which involved a NRF52840 and a MX25R6435F (so same...
Dear Nordic Support,
My project is split into two parts: A firmware application that is based on the Generic Level Server model example (from the Mesh SDK) and an Android...
Good morning,
I'm working on nRF5 SDK v17.0.2 and I am using Segger Embedded Studios (SES) for the development.
I'm having a problem when I want to share my project...
I'm aware that the nRF CLI tools are not yet ported to AArch64 so they don't work natively on Apple Silicon. Normally rosetta 2 is fine, but nrfjprog is not compatible with...
working with nrf52832, sdk 16.0 s132 v7.01
in the uart example i get to this place in the code :
i get a pin toggle which makes my system do some unwanted things...
