Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
Hi. I'm using nRF52832, SDK13.0.0.
I want tuse SHA256 abd MD5.
Could you let me know which function is for SHA256 and MD5?
Actually I've tried my code as below.
uint8_t...
Current (as of today) version of NCS wont build device tree out of the box.
Output using cmake+ninja (but same if using emStudio):
-- Using application from '/home/jesper...
Dear Devzone members,
I need your suggestions about one thinkg.
I am trying to do sensor networking with nRF52840 tags.
I have 15 slave, 1 master. All slaves work...
So I'm trying to do some simple store and load from and to my flash memory. I'm using the nRF51822 with 256 kB flash memory. My problem looks exactly like this one, but of...
Hi.
I tired searching around the web but I did not find clear information about this. Maybe the answer is too obvious for anyone to write about.
Problem that i'm facing...
HI, I recently used nRF905, a one-to-many intercommunication project, because one-to-many will send corresponding instructions for machines with different serial numbers,...
I'm working on nrf51822 , Softdevice S110. I have implemented whitelist in my application its working fine. But ion some cases i need to disable the whitelist option ( because...
Hello Nordic Staff,
I am using the NRF52832, SDK 15.3, Keil, and the NRF52 dk dev kits. I want to modify a program such as the UART central example to recognize my custom...
I'm measuring the current consumption of udp_with_psm program reading this post, and the current is very high. why?
https://devzone.nordicsemi.com/nordic/cellular-iot-guides...
Dear Nordic. I am working in the device that require the controller to measure its VDD line to ensure that the the device goes into sleeping mode (very low current and do...
Is there any code example for Android or iOS on how to build / send a DFU request for NRF_DFU_OP_FIRMWARE_VERSION and then how to interpret the response that comes back? ...
I want to receive data through UDP in eDRX
I tried to set up non-blocking UDP by reading this post, but I can't achieve the function yet. Any help? https://devzone.nordicsemi...
Hi all,
I am successfully using Openthread for an application on the nrf52840. As the application is growing I'm thinking about utilizing a RTOS. Therefore, I am currently...
Hello. I have integrated signature validation before boot in my boot loader. This uses the `nrf_dfu_validation_boot_validate` function, which eventually calls into `nrf_crypto_backend_secp256r1_verify...
I use the above code to copy the device root key from the flash region. The if condition at the end results to FALSE always whcih implies that the key was not copied into...
